2002 Hyundai Getz Logo

Related Topics:

A
Anonymous Posted on Feb 22, 2015

How to remove the starter motor on a Hyundai getz

5 Related Answers

Anonymous

  • 53 Answers
  • Posted on Oct 18, 2008

SOURCE: hyundai getz

if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable

Ad

Anonymous

  • 776 Answers
  • Posted on Jun 05, 2009

SOURCE: hyundai getz radio

Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg

Anonymous

  • 566 Answers
  • Posted on Mar 10, 2010

SOURCE: logbook service for a hyundai getz

hi from uk did you not recieve the wallet containing the owners handbook/service reciord book/ radio instructions book? this comes with car if you bought new ? check with dealer and ask for it? there is a market for these books and are valuable yours may have been taken ??

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Apr 25, 2012

SOURCE: how to bleed my hyundai getz diesel pump

Loosen all the lines at the fuel injectors and crank the engine until the air bleeds out and then tighten the lines, you may have to do this twice.

Bill Boyd

  • 53816 Answers
  • Posted on Mar 18, 2013

SOURCE: how to replace hyundai getz clutch

This ia a big jobunless you have mechanical knowledge. I suggest you get a manual and read up before you tackle this job. If you have no experience it would be cost effective to have this job done in a clutch and brake shop

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
1answer

2004 Hyundai Getz 1.3. Good day. I am looking for the torque settings for big ends and mains please?

Question edited for clarity, too many words :>D
Question moved to model category.

They are all in this link

https://www.hyundai-forums.com/threads/hyundai-getz-1-3-2005-g4ea-big-end-torque-settings.639857/

Hyundai Getz 2003 1 1 1 3 PDF

Scribd https://www.scribd.com > document > 138325436-HYU...
Tightening torque Main bearing cap bolt 1.3: 55 ~ 60 Nm (550 ~ 600 kg.om, 41 ... big end bear- ing. Crankshaft end play 1.3L: 0.05 ~ 0.175 mm (0.002 ~ 0.005 ...

..
1helpful
1answer

Removal of 2008 hyundai getz engine

Watch the video's on Youtube
DIY Part Hyundai Elantra transmission engine swap 1 of 3 Removing the...


It is not an exact match but the procedure is typical.
0helpful
1answer

How to change stop light globe on 2008 hyundai getz

Remove the two 10 mm (head) bolts that hold the stop light. This bolts are between the tail light assembly and the tail gate weatherstrip. You can see them without having to remove anything.

By using a masking tape wrapped flat screwdriver, pry "back" the whole tail light assembly. Once out, you can twist the brake light (or reverse, or turn signal) bulb plug, remove and replace the bulb.

The Getz uses standard two filament brake globes (1/4 turn to install).
0helpful
1answer

Torque settings for 1.4 hyundai getz , main bearings

I need torque settings on hundai getz 1.4 Mains and big ends
1helpful
1answer

Restart a getz after a year lying idle

This might be a good thing at this stage. The engine may have water in the cylinders, depending on where the car was.
First remove all the spark plugs and make sure they are clean and gapped correctly. Poke a length of wood dowel or a stout straight stick carefully into the plug holes to check for any water in the cylinders. This must be removed if present. The best tool is a turkey baster or a length of clear plastic hose, to **** it out.
Check the air cleaner housing for water, and remove any found. Renew the element there if required.
Then there is a choice. You can squirt a tablespoon of engine oil in each cylinder, then leave it to soak for a day or 2, or use a commercial product
http://www.seized-engine.com/used-car-engines.html
1helpful
1answer
22helpful
2answers

How to change hyundai getz brake light in light cluster?

On the Getz remove 2 screws on the outside then gently prise the cluster off from the dowels as above.
9helpful
2answers

Hyundai getz radio

Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg
Not finding what you are looking for?

1,748 views

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...