Are that you joints part of the front wheel bearing assembly

in order to get that u joint out...you need to remove the wheel bearing assembly so you can remove that axle assembly and replace the u joint

cv joint or wheel bearing jack up car check for slack up & down & side to side (wheel bearing) put in neutral and turn tire listen for noise (cv joint)

Wheel Spindle, F-150, F-250, F-350
Removal

1. Raise the front of the vehicle and install safety stands.
   

1. Remove the wheel and tire assembly. Refer to Section 04-04 .
   

1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
   

1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
   

1. Remove the rotor from the front wheel spindle (3105).
   
   
   
   
   
   Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
   (57-75 Lb-Ft) B - Tighten to 68-92 Nm
   (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)

1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
   

1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
   

1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
   

1. Remove the cotter pin and castellated nut from the lower ball joint stud.
   

1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
   

1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
   

1. CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
   Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
   

1. Remove the front wheel spindle and ball joint from the axle.
   
   

Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal

1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
   

1. NOTE: Lower ball joint must be removed first.
   
   Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
   

1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
   

1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
   
2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
   Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.
   
   
   Installation
   
   1. CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.
      
      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.
      
      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
      
   1. Turn forcing screw clockwise until ball joint is seated.
      
      
      
      
   

Removal Steps

1. Torsion bar

2. Wheel speed sensor

(if equipped with ABS)

3. Back plate

4. Lower ball joint

5. Upper ball joint

6. Knuckle assembly

7. Oil seal

8. Thrust washer

9. Needle bearing

10. Knuckle

Installation Steps

10. Knuckle

9. Needle bearing

8. Thrust washer

7. Oil seal

6. Knuckle assembly

5. Upper ball joint

4. Lower ball joint

3. Back plate

2. Wheel speed sensor

(if equipped with ABS)

1. Torsion bar

The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

Hi, this could be caused by worn ball joints or worn wheel bearings. If the whole hub moves look at the ball joints to determine the play on the joints, if the wheel moves and there are no movement on the ball joints, then you need to replace the wheel bearings.

There is only one wheel bearing in each wheel assembly. Are you sure the bearing is the source of play and not a tie rod end, ball joint, or even the lug nuts?

It could be an indication of a bad wheel bearing assembly. Did you check the lug nuts to be sure they are tight? It could also be the tie rod assembly. I would take off the wheel and try to move the just the hub assembly. Do you hear any screeching/squealing noises? Any popping while you are driving? Are your tires wearing? All these are classic signs of a bad wheel bearing. Any decent tire/auto shop can put your car on a lift and check the wheel bearings.

remove front wheel brakes,rotors, axle nut,remove the four bolts on the bake side of your unit bearing using one of the 4 bolts removed from the unit bearing (also knowin as wheel bearing) go get a half dozen of the same bolt only 1 to 2 inchs longer theard them into the unit bearing from the back side and start beating. the unit bearing is a sob to get out but will come out with time once you get it out pull out your axle shaft replace the ujoint and reassemble anti seize everything as you re assemble it

http://groups.yahoo.com/group/villagerquest/


Item Part Number Description 1 — Cotter Pin 2 — Nut Retainer 3 1131 Insulator 4 3B477 Front Axle Wheel Hub Retainer 5 1195 Front Wheel Outer Bearing Retainer Washer 6 1104 Wheel Hub 7 1107 Lug Bolt 8 3K050 Snap Ring 9 3123 Front Wheel Bearing 10 2K004 Front Disc Brake Rotor Shield 11 3130 Front Wheel Knuckle

Wheel Hub, Wheel Knuckle and Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Tie Rod End Separator T85M-3395-A
Removal

1. Raise and support the vehicle.
   
2. Remove the wheel (1007) and tire assembly.
   
3. NOTE: It is not necessary to disconnect the front brake hose (2078).
   
   Remove the disc brake caliper (2B120) and suspend it with mechanic's wire out of the way. Refer to Section 06-03 for the removal procedure.
   
4. Remove the front disc brake rotor (1125).
   
5. Remove and discard the cotter pin.
   
6. Remove the nut retainer and insulator.
   
7. Remove the front axle wheel hub retainer (3B477) and the front wheel outer bearing retainer washer (1195).
   
   
   
   
   
8. Remove and discard the cotter pin from the front suspension lower arm ball joint (3050).
   
9. Loosen the front suspension lower arm ball joint nut until it contacts the front wheel driveshaft joint.
   
   
   
   
   
10. Strike the front wheel knuckle with a hammer while pulling down on the front suspension lower arm (3078) until the front suspension lower arm ball joint separates from the front wheel knuckle.
    
    
    
    
    
11. Remove the front suspension lower arm ball joint nut.
    
    
    
    
    
12. Remove the front suspension lower arm ball joint from the front wheel knuckle.
    
13. Remove and discard the cotter pin.
    
    
    
    
    
14. Remove the tie rod end nut.
    
    
    
    
    
15. Use Tie Rod End Separator T85M-3395-A to separate the tie rod end (3A130) from the front wheel knuckle.
    
    
    
    
    
16. Remove the front brake anti-lock sensor bolt.
    
    
    
    
    
17. Remove the two front shock absorber-to-front wheel knuckle nuts.
    
    
    
    
    
18. Remove the two front shock absorber-to-front wheel knuckle bolts.
    
19. Remove the front shock absorber (18124) from the front wheel knuckle.
    
20. Use 2-Jaw Puller D80L-1002-L, or equivalent, to separate the front wheel driveshaft and joint (3B436) from the front wheel knuckle.
    
21. Remove the front wheel hub, front wheel knuckle and front wheel bearing as an assembly from the vehicle.
22. If necessary, match mark and remove the steering stop bolt and steering stop bolt jam nut from the front wheel knuckle.
    
    
    
    
    

Installation

1. Position the front wheel hub, front wheel knuckle and front wheel bearing as an assembly on the front wheel driveshaft and joint.
   

1. Install the front wheel knuckle into the front shock absorber.
   

1. Install the two front shock absorber-to-front wheel knuckle bolts.
   

1. Install the two front shock absorber-to-front wheel knuckle nuts. Tighten the front shock absorber-to-front wheel knuckle nuts to 113-123 Nm (83-91 lb-ft).