How do I remove the inside Rear view Mirror?

glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the outside rear view mirror access water shield.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect and remove the speaker.

1. Disconnect the outside rear view mirror electrical connector.

1. Remove the outside rear view mirror.
   1. Remove the nuts.
   1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.

Most mirrors have a very small allen screw that you have to losen then the mirror will have to be slid up towards the roof of the car and it will slide off the metal piece that is glued to the windshield

Hello, to replace the rear mirror, try the following:

1. Roll the passenger side door window all the way down. Turn off the ignition and remove the keys.


2. Gently pry the window control panel from the arm rest with the pry tool or screwdriver starting at the bottom of the panel. Flip it over and unplug all the wire harness outlets from it. Set the panel aside.

3. Locate and remove the two panel door plugs near the arm rest concealing the two screws and remove the screws with the Phillips head screwdriver.

4. Remove the door panel retainer plugs along the edge of the door by pressing in the middle of the plug to unlock it and removing the plug.


5. Detach the mounting triangle from the upper inside door panel covering the side-view mirror.

6. Remove the door panel by lifting outward and then upward. Disconnect the speaker wire harness from the underside of the door panel and set the door panel aside.

7. Locate and disconnect the mirror wire harness.

8. Pull back the foam insulation from the inside panel covering the side-view mirror.

9. Unscrew the three mounting nuts from the mirror using the ratchet, extension and a socket. Do not drop the nuts into the door cavity.

10. Pry the mirror gently away from the outside of the door.

11. Install the new mirror and replace the mounting nuts on the mirror studs and tighten with the ratchet, socket, and extension. Plug the mirror wire harness back in. Replace the foam insulation. Replace the mounting triangle.


12. Replace the door panel by reversing the procedure. Start by plugging in the speaker wire first.


Thanks

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

There is a small screw in the mirror, an allen (or hex) wrench fits in it.

SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the upper speaker.
   1. Disconnect the electrical connector.
   1. Remove the bolts.
   1. Remove the speaker.

1. Position the watershield aside.

1. Remove the exterior rear view mirror access panel.

1. Disconnect the exterior rear view mirror electrical connectors.
   • Release the wiring harness locator.

1. Remove the exterior rear view mirror.
   • Remove the bolts.
   • Feed the wiring harness through the door opening.

1. Remove the front door trim panel (23942) ; refer to Section 501-05 .
   • Peel back the watershield.

1. Remove the rear view mirror mounting hole cover (17K709).

1. Disconnect the power mirror electrical connector.

1. Remove the outside rear view mirror (17682).
   1. Remove the screws.
   1. Remove the outside rear view mirror.

please rate as fixya if this works for you.

As the owner of a 2001 Grand Prix GTP I can tell you that the mirror you speak of is not terribly difficult to replace, but you need the tools to remove the inside panels in the front corner of the window to get to it. Once you get that off there should be three bolts/nuts that hold the mirror on and if you have power mirrors then of course you'll have an electrical connector in there as well.

I dont have any instructions wrote up but there is a Grand Prix car club forum you can check that may have some information on how to replace it in more detail. You can go to grandprixforums.net, sign up and post up your problem and Im sure someone there will probably have specific instructions.

go to auto parts store they sell a repair kit w/ an adhesive for about $1.50 that will glue the mirror back to windshield! remove old glue with a razor blade and clean 1st

there shoud be a little torx scrw holding it on remove it its either a t10 or t15 torx driver