1996 Dodge Intrepid Logo

Related Topics:

JB Turner Posted on Feb 12, 2015

How do I remove ashtray bulb on 96 Dodge Intrepid

5 Related Answers

Anonymous

  • 24 Answers
  • Posted on Apr 05, 2009

SOURCE: How to check transmission fluid on my Dodge Intrepid 96

Yes, but you need to have it in nuetral

Ad

Anonymous

  • 187 Answers
  • Posted on May 11, 2009

SOURCE: Car won't start - 96 DODGE INTREPID

Check the auto chock.

Anonymous

  • 35 Answers
  • Posted on Jul 14, 2009

SOURCE: 96 intrepid and not getting fire?

hope to be some help, it sounds like the car aint geting any gas,my advice is too check the gas line & fuel pump...let me knw how it go...

Anonymous

  • 1305 Answers
  • Posted on Oct 14, 2009

SOURCE: How to remove the harmonic balancer on a 1995 Dodge Intrepid 3.5

There is a nut in the center of the balancer... loosening may require an "impact" or a sharp blow with a hammer to begin to loosen the nut. Once loose, you can use a harmonic balancer puller (rentable at a local rental yard) Since its a very tight fit you'll need the puller to persuade it loose from the crankshaft.... watch your knuckles...

Anonymous

  • 1 Answer
  • Posted on Jan 24, 2010

SOURCE: 01 Dodge Intrepid headlight wiring

there should be 3 wires. The all black one is the ground, the black wire with the colored line is the positive, and the other is the negative

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I replace left rear turn signal on dodge intrepid?

Open trunk, pull carpet back (may have to undo some fasteners). The tail light assembly should be visible. Unscrew the plastic fasteners to the tail light. The whole tail light assembly should now be able to be removed from the outside of the car. You will see the individual bulb sockets where the wires lead to the bulbs. Twist to remove. Take the burned out bulb to the car parts store. Reverse these steps to reassemble.
0helpful
1answer

How do you change tail light bulb on 1997 Dodge Intrepid?

In the trunk. You will find black plastic wing nuts that hold the felt panels in place, remove and pull back the panel pieces and you can now access the taillight assembly, if you can't access the bulbs from that point you need to remove the tail lights by un bolting the 10mm nuts holding the taillight assembly then remove the taillight from the car now on the outside you should be able to access the bulbs from there by turning the bulb plugs about a 1/4 to a 1/2 turn, reassemble the taillight and interior panels.
5helpful
2answers

How do i change the ashtray light?

Remove the ashtray and look for the screws that attach the ashtray bracket to the dash. Remove the ashtray bracket. The light fixture has a metal clip that you can squeeze to release the fixture from the ashtray bracket. (Sometimes it is easier to pry or push the clip gently sideways with a small screwdriver.) Replace the bulb and re-assemble.
2helpful
1answer

How do you replace head light bulbs in a 2003 dodge intrepid

On each headlamp, you need to remove the screws holding the headlamp the the car (2 screws per headlamp)
Then pull the lamp out and change the bulbs.
Dont touch the new bulbs with your hands, use the plastic bag they came in (but remove the bag after install!!!)
1helpful
1answer

How to change out a head light bulb in 1999 Dodge intrepid

remove the two bolts that hold the whole headlight assembly in and pull it out and change your bulbs.
0helpful
1answer

How do you replace headlights 94 dodge intrepid

The headlight bulbs are inserted into the headlight housing. To remove the bulb, disconnect the wiring harness, then twist the bulb housing to remove the bulb. Insert a new bulb and install the wiring harness.
0helpful
1answer

96 intrepid and not getting fire?

hope to be some help, it sounds like the car aint geting any gas,my advice is too check the gas line & fuel pump...let me knw how it go...
0helpful
1answer
2helpful
1answer
1helpful
1answer

HOW CAN I CHANGE THE BULBS FOR THE MAP LIGHTS AND THE CIGAR ASH RECEIVER WITHOUT BREAKING ANYTHING.

To change the bulbs for the map lights you need to first remove the screw located on the overhead console which is towards the front of the console (towards the front window). Then you need to pry down on the rear of the console. Once the console is removed you then need to remove the map light bulbholders and replace the bulbs.

As for the bulbs for the ashtray I am not sure if there is one.
Not finding what you are looking for?

66 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...