How do I remove the lower front control arm on a 96 Nissan 200sx

You need to loosen the torsion bar adjusting bolts until all the tension is removed, remember to mark a reference point from bar to frame so you can get close to the correct riding height after reassembly. Can't tell if you split the ball joint from the knuckle from your explanation but a couple of good solid whacks to the lower knuckle will unlock it. Mark & remove the control arm bushing bolts and use a pry bar to push out arm @ bushings.

no sorry different patterns
88 ford escort 13 inch 4x108
96 Nissan 200sx se-r 15 inch 4x100

to remove lower control arm bushings you need to remove control arm from vechicle have control arm bushings pressed out.you need to remove disconnect torsion bar,remove shock absorber,disconnect stabilizer bar link, remove axle half shaft, remove the lower ball joint, remove control arm mounting bolts, then remove lower control arm.

UPPER CONTROL ARM:

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.

1. Raise and support the vehicle safely.
2. Remove the front wheels. Support the lower control arm assembly with a floor jack.
3. Separate the upper ball joint from the steering knuckle using a ball joint separator tool.
4. Remove the self-locking nuts from the upper arm anchor bolts. Remove the upper arm from the vehicle.

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.

Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

It's the diode block. The switch is fine, but the diode block controls the speeds. It's about a $20 part and located under the dash next to the fan on the passenger side. It's held in with two screws and shouldn't take you more than 20 minutes to replace.

LOWER CONTROL ARM

REMOVAL
1) Raise and support vehicle. 3) Remove the steering knuckle.
Remove the bolts fastening the power steering cooler to the front suspension cradle crossmember reinforcement (Fig. 21). 5) Remove the lower control arm rear bushing retainer bolts located on each side of each lower control arm rear bushing. NOTE: The bolts fastening the cradle crossmember reinforcement are of three different thread sizes. Note the location of the various sizes.

6) Remove the bolts attaching the cradle crossmember reinforcement to the front suspension cradle crossmember (Fig. 22). Remove the 2 bolts fastening the reinforcement and rear of cradle crossmember to the body of the vehicle. Remove the reinforcement. 7) Remove the pivot bolt attaching the front bushing of the lower control arm to the front suspension cradle crossmember. 8) Remove the lower control arm.

Use a piece ot 2by1 put between the alternator and the block, lever the alternator away from the block gently while rocking it up and down.
You will see a small spacer,tube shaped, that tends to jamb against the bottom bracket..
Just to clarify, you have taken out the top bolt,in a long slot for adjusting the belts tension,and the two lower bolts, 1 at front and 1 at rear of alternator.

This is for the 2 litre SR20DET engine so not sure if that's what you have - never heard of a 1.6 version. Below is the exploded diagram and a test for the sensor.

Hi,
Remove the castle nut on top of the ball joint that secures the ball joint to the spindle. separate ball joint/lower control arm from spindle.Remove lower control arm bolt attatching control arm to subframe/engine cradle. Remove control arm. Replacement is recersal of the removal. Nissan/Infinity ball joints can not be pressed out or in. They are replaced with the whole new lower control arm as one (On most Nissan/ Infinity vehicles, although some exeptions apply. Hope this helps.
Daniel G.