Question about Lexus Cars & Trucks
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
If your is exhibiting the same signs as a dead battery it really sounds like your alternator is bad. If you are handy, you can remove the alternator and take it to an autoparts store like autozone and they will test it for you. This is not a hard job to do, usually 2 electrical connections, 3-5 mounting bolts and you have to pop the belt off. Just reverse it to install a new one. Good luck! - Nick
Posted on Nov 03, 2008
I just changed the cabin filter of my ES300. I found the instructions on the manual, under airconditioning and audio. It's pretty easy to do. I bought the filter from Kragen's for $21.95.
Posted on Mar 27, 2009
SOURCE: 2000 Lexus ES300 - 45K
Are you sure this is a rattle or is it more of a creaking noise? I have a 2000 ES300 and had an issue when I would go over speed bumps and the noise would drive me nuts! However replacing the bushing in the top of the strut mount is expensive due to the labor involved.. Replacement of the strut or the bushing isn't necessary. Just open the hood, locate the strut housing and you ll be able to see the black rubber bushing in the middle. Obtain a can of Heavy Duty silicone aerosol spray and attach a straw to the spray tip. Using a flathead screwdriver wedge the screwdriver between the top of the bushing and the metal pushing the screwdriver all the way to the edge of the metal underneath the roof of the metal housing. Then pry the edge of the bushing away from the metal housing so that the top of the edge of the bushing exposed and stick the straw end of the silicone into the spot and spray generously. Only slight bushing movement will be obtained as the bushing is pretty stiff but it will be enough. Work your way around using this technique until you get the spray fully around the bushing 360 degrees getting it into the area between the edge of the bushing and the metal. Then spray the silicone onto the top of the bushing filling it all the way up until it spills over the metal. After it drains down, repeat again making sure you fill it above the rim of the bushing so it seeps into the area between the bushing and he metal housing (or frame) because this is where the rubbing is taking place that is creating that awful noise. Repeat on the other side and your done. The main goal is to get the silicone into the area between the metal and the bushing along the edge. This happens to be the way I was able to do it. This totally solved my problem and now the car is so quiet there aren't any knocking, creaking or rattling noises. This was a hard solution to explain without visuals, hope you can follow. This will work for sure. The Heavy Duty Silicone spray I used was manufactured by CRC and I bought it from Walmart.
Posted on Jul 22, 2009
My Son has a 95 es300, the amp for it is located under the front passenger seat. The easiest way to access it is to remove the 4 bolts holding the seat down, and remove the seat. Takes about 5 minutes
Posted on Jul 24, 2009
i got a 1996 chev. blazer s-s10 4.3 engine 4x4.problem i got is i got 1st 2nd & overdrive & reverse but no 3rd gear what should i do
Posted on Jan 19, 2010
Tips for a great answer:
Mar 22, 2017 | 1999 Lexus ES 300
Sep 21, 2016 | Lexus ES 300 Cars & Trucks
Jan 27, 2016 | Lexus Cars & Trucks
Nov 24, 2013 | Lexus Cars & Trucks
Sep 18, 2012 | 2003 Lexus ES 300
Aug 17, 2010 | 1998 Lexus ES 300
Apr 17, 2009 | 1997 Lexus LS 400
44 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: