2005 toyota sienna xle. I already had the codes read....I know its it's ox censers or cat converters. I'm not putting thousands into this van. I just want to know where the PCM fuse is so I can pul

Interior Fuse Box Location 2004 2010 Toyota Sienna 2005 Toyota Sienna XLE...

2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube

it costs nothing to have the codes read at auto parts stores. If you want not to waste money then read the fault codes first

Take it to a car parts store like Advanced Auto to get their free trouble code reading service.

what body, CE, LE, XLE or XLE limited?
this car has 2 system.s (option) front and rear, are both bad?
or just the front? you said only rest of van.
the front has 2 options, manual and auto controls panel.
which one you have?
i see no cables. that leaves damper motors or vacuum servos.
a real tech tests the controls, first. if they are good
he look in the FSM for the damper motor tests.
its there. and he hot wires it and finds, bingo, its bad.
and replaces it. labor can hit hr on dash pulls. 8hrs. work.

find another mech.
the parts are sold at Toyota. look there , in the parts sections
see it, see those parts.? sure are... there.... need help looking ask.
the dampers are bad.
a real mech finds out which damper is bad
if its a motor , he buys a new damper motor at TOY. for $150
if its just a cable it fixes that...

it can be 3 things
1: control bad. even a blown fuse.
2: connection from 1 to 3
3: bad damper motor.

bad parts 4,5,6? (part 6, mode motor bad?)
http://www.trademotion.com/parts/2005/Toyota/Sienna/CE?siteid=214001&vehicleid=185020&diagram=8530070



FIRE HIM!

look on youtube, there are thousands of car repair videos there

Brake loose connection between cat and exhaust manifold , it will allow exhaust gas to go out before cat , and see if it's restore the power on the engine.
If it does then your cat is clogged.
If not it's also might be Throttle Position Sensor , or Mass Air Flow Sensor.
You can't remove cat , you have to replace it if it's bad. Cat is a part of Emission control system.

you may have worn front end parts , have frt end checked you dont want to loose your steering good luck.

This may or may not work depending on exactly what is wrong with the door, I cant tell what is wrong without looking at it directly however:
You can try starting with all doors closed and unlocked, keys in hand disconnecting the battery and letting the vehicle sit for 2 min or so, then reconnect the battery. Put the key into the ignition and turn it to the on position but do not start the van. Next press the button to disable the power sliding door for the drivers side, then manually open the door fully, wait 5 seconds, then close it manually fully. Press button the button again to re-enable the power sliding door, then try to use it with the automatic feature either by pulling the handle or using your remote, this may or may not work depending on if the door has somehow become de-initialized (it should work now) however if something is broken inside the door closing mechanism or door closed/open sensors, the door will continue to malfunction.

API 'SJ' 5w30 and it holds 5 qts with oil filter. Great van! Good luck with it. Curt