I locked my keys in my car, does anyone know a way to open it without a key?

To arm content theft alarm.
1. Open the door.
2. Lock the door with the power door lock switch or
the remote keyless entry transmitter. The
SECURITY light should flash.
3. Close all doors. The SECURITY light should go off
after approximately 30 seconds. The alarm is not
armed until the SECURITY light goes off.

If a locked door is opened without the key or the remote keyless entry transmitter, the alarm will go off. The headlamps and parking lamps will flash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power.

Try this

2004 XL7

1. Remove key from ignition switch.

2. Close all doors.

3. Open drivers door

4. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

5. Within 20 seconds Close and open drivers door 3 times.

6. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

7. Locks should now lock and unlock automatically to confirm you
have entered programming mode.

8. Press the UNLOCK button on remote and locks should cycle to
confirm programming.

9. Repeat step 8 on each additional remote.

10. Exit vehicle with keys and remote, close door test remote(s)

You have locked yourself out of a vehicle that has one of the most "overengineered" and theft resistant security systems known to man.. If you are locked out do not, repeat DO NOT ALLOW anyone or you yourself attempt to gain entry with a "slim jim". Just trust me without further explanation. The only method i know to be succesfull without damage is the "wedge" method. Best done by someone with experience like a AAA/towtruck driver. Rubber or wood wedges are inserted or wedged in between the upper door frame and the roof panel opening up a gap sufficient to work some long tools to trigger the door lock. Once you get the door open Im assuming you will have your key which will disengage the engine "immobiliser" when the ignition is turned. If youve lost your key there is no option except to visit your Rover dealership parts department, title/registration and ID in hand, to order a new laser cut key. Usually about three days for the key only and about a week and $200+ for the flip out key remote. Hope this helps. feel free to post more info/questions, ill do my best to help. Good luck!

if the key does not turn the lock spray it out with wd 40 run key in and out of lock few times.because everyone uses remotes to open their cars the waffers in the door locks get coroded and wont fall in proper place when key is inserted.give it good cleaning and see if it will unlock

put key in ignition turn key to number 2 lights on dash battery etc. then press the fob. till the doors lock then it is rest.

I know this question is old but I recently encountered a similar problem with my 1995 323 BA and this may help someone else. Override the immobilizer by doing the following:


open the car via the drivers door
put the key in the ignition
turn the key to ACC
now turn the key to ON
repeat the last 2 steps X 12 quickly (ignore the indicators flashing and the central locking activating).
the dashboard should be lighting up as normal.
Now turn the key to START

Key must be made by the dealer and programmed to the vehicle. There is a chip in the key that the antitheft system must read to start the engine. Any key blank with matching cut can open the door, no chip necessary

i tried this my self on my car without calling or using nothin big but a smaller car key just move the smller key around so it can move the seal and keep movin the door handle it should pop the lock if you move the seal to open the lock

hi, to program the keys to the vehicle is quite simple

1) open the vehicle, sit inside and close the door

2) insert the key in the ignition and turn to position 1 so that just the air bag light illuminates

3) press and hold the unlock button on the key and remove the key from the ignition (do not release the unlock button)

4) while still holding the unlock button with the key removed press the lock button 3 times

5) release the unlock button on the remote and the door locks should lock and unlock if the proceedure has been carried out correctly

6) to program any other key(s) press and hold the unlock button on remote and again press the lock button 3 times but do not insert it into the ignition or turn the ignition on as done previous.

you may want to print these instructions and read them a few times before proceeding, if you muck up the process while programing keys, no harm will be done, you just have to start the process over. hope this is of some help, regards mark.

ok get in the car, close the door, make sure all doors are closed.... put the key in the ignition, turn the key to on but without starting the car (lights on dash light up only) press and release the key lock button, turn key to off, without removeing the key.. turn to on without starting the car (dash lights up only) press and release the key lock button again, turn the ignition off, without removeing the key then turn back on (lights on dash on only without starting the car, press and release the key lock button , turn off the ignition without removeing the key, ..turn on the ignition once more without starting the car , press and release the key lock button and u should hear the door lock cycle ....leave the key in the ignition ... now press the lock button or unlock button on the other remotes one at a time if u have them.....u should hear the lock cycle indicateing all remotes are programmed.... kind of tricky to explain but you will get it, the sequence of turnin the key in the ignition on and off is only done with that one first key,,, remember after the door lock cyles press the lock or unlock button on the other remote fobs if if any...and ur done..may take u a few trys.. let me know how it worked out.