Question about 1991 Ford F150

3 Answers

Fix the hyd. clutch in my 1991 f-150 It gose all the way to the floor

MY clutch is on the floor and gear won't change.

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 715 Answers

Check the fluid level

Posted on Dec 26, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 51 Answers

Check fluid level in clutch master cylinder. If low or empty check for leaks. If empty, no leaks try filling and bleeding the air out.(the bleeder is on the slave cylinder if it has a piston type cylinder). If that doesn't solve it you need a new slave cylinder or master cylinder for the clutch.

Posted on Dec 29, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 18 Answers

Your slave cylinder is most likely going out. if you fix that you should change the Throwout Bearing Pressure Plate clutch , alway get the heavy duty package. and inspect the folk... that holds bearing , well it holds bearing in place as the bearing goes up n down the transmission

Posted on Dec 26, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a ford fiesta r reg its had a new clutch the clutch has only been in for a week and half i started having problems when i went to go shopping i put it into gear and i only had a little bite


Who replaced the clutch? if it was a shop then I would take it back for them to fix, If you changed it yourself was there oil on the old clutch and if so did you repair the oil leak. I.e. hyd clutch or transmission seal. Hope this helps.

Apr 14, 2015 | Ford Fiesta Cars & Trucks

1 Answer

Clutch pedal stay floor


Usually means a broken clutch cable or bad clutch hyd cylinders. Check fluid levels first.

Dec 19, 2013 | Renault Cars & Trucks

1 Answer

I have a suzuki xl-7 2005 manual and is hard to change gear does this mean the clutch is gone or is there a easy fix


This is pretty easy to trouble shoot.
first off , assume it's a simple easy fix. it can be.
not 8 to 10 hours labor jerking the tranny and 4wd parts.etc.
hard to change gears can mean many things.
1: cant select. this is common, the shifter tip has 2 plastic parts
that cause the shifter to do 2 things, its loose as heck and
cause , SELECTION failure. that is ,you can not move the shifting
forks inside the tranny. is the reason, this is shifter failure.
Suzuki sells the parts, ,shown in link below.

2: hard to shift , #2 is , but you can not force any gears
reverse is the most difficult. and if you try hard enough
the transmission grinds. this is clutch failure. (1 of 2, ways)
3: if the clutch is failing, called DRAG. (not slip, no noise or chatter)
you can jackup the rear of car, at the axle place 2 jack stands
under said axle housing ends and now you can shift.
proving a bad clutch as it now shifts but in a clunky way.

ok, now we are in the Dragging bad clutch fails.
the first easy fix, is easy.
is called,a "bad clutch actuator"
on early cars this part is a cable (replace the cable)
on later cars the actuator is a MC/slave hydraulic pedal sys..
The cable clutch you do...the.. do the 1 inch test. see link.
on Hyd. do the 3/4 inch test. see the link.

this proves the clutch is good or bad , every time.
if the clutch lever fails to move the correct distance.
no clutch can work, fix the actuator first.
this page gets them all.

http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Sep 14, 2013 | 2005 Suzuki XL-7

1 Answer

Kia Sephia 5 spd won't shift gears


You need to bleed the lines with a special tool, contact the dealer on this.

Jun 13, 2012 | 2000 Kia Sephia

1 Answer

How do you bleed the clutch on a 1995 dodge stratus


Sounds like the slave cylinder inside bell housing is leaking. Replace both cylinders when fixing. the clutch plate and flywheel should be inspected for wear.

Mar 06, 2018 | Dodge Stealth Cars & Trucks

1 Answer

94 toyta pickup chage starting hard shifting gear replace slay slender not solve -change clutch not slove problem change clutch hyd master cylender not sloved broblem some one say chage transmission- what...


If you're sure that the clutch hydraulics are working properly ... then you are going to need to pull the transmission to see why the release isn't working .... bad throw out bearing, problem with pressure plate or ??

Trouble shooting here:
http://www.ncttora.com/fsm/1993/clutch/1troubles.pdf

Aug 21, 2011 | 1994 Toyota Pickup

1 Answer

91 nissan pathfinder 5 speedmanual.... Clutch pedal feels stiff and when i start it in gear the truck lunges forward like the clutch it still engaged.... Master and slave have been replaced and all hyd....


It really sound like you are going to need a new clutch. If the slave or master cylinders were bad they would feel loose, a stiff pedal usually means something came apart in the pressure plate.

Jun 03, 2011 | 1991 Nissan Pathfinder

1 Answer

Cant change gears


im having the same probem. does the clutch pedal go to the floor easily. if so its the hydraulic clutch line. but i still havent found anything on how to fix it

Sep 20, 2009 | 1987 Jeep Comanche

Not finding what you are looking for?
1991 Ford F150 Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...