Question about 2010 Ford Mustang

1 Answer

2010 mustang v6 input speed sensor code po 715 where is it ?

Everything I can think of output replaced cant find input?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 210 Answers

That is the input/turbine speed sensor circuit malfunction. or turbine shaft speed sensor. it tells the car when to shift.

Posted on Dec 24, 2014

Testimonial: "I know that WHERE IS IT."

  • john starr
    john starr Dec 24, 2014

    I KNOW THAT .WHERE IS IT?

  • free again
    free again Dec 24, 2014

    mounted on the top of the transmission case

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I ran over a branch in the road with my 2010 ram and I have codes po 721 and po 933 where do I start to look if I pulled a wire?


One is to a hydraulic pressure sensor that I would think will be around the transmission and the other is to the output shaft sensor. It also should be on the side of the transmission.

Oct 05, 2013 | Cars & Trucks

1 Answer

2012 ford mustang


Code 315 involves the crank sensor, and code 715 involves the speed sensor in the transmission.
Both sensors would need to be checked, and I would think the car is still covered under the factory warranty.

May 12, 2013 | Ford Cars & Trucks

1 Answer

Po731 and Po715 on '96 grand caravan


Code 731 is for the computer thinks the ratio is wrong for first gear, and code 715 is for a problem with the input speed sensor. Code 715 could cause code 731.
Someone would need to check the sensor and possibly replace it.

Aug 03, 2012 | Dodge Grand Caravan Cars & Trucks

1 Answer

Check engine light po 731


Diagnostic Test Code (DTC) P0731 is a transmission fault code and has a generic description of "GEAR RATIO ERROR IN FIRST GEAR".

The Powertrain Control Module (PCM) monitors the input shaft speed and the output shaft speed of the transmission through the input and output speed sensors. The proper gear ratio will produce a predictable difference between the two sensors. This DTC sets when the expected difference differs greatly from the actual difference between the two speed sensor readings.

This can be caused by several things including:
> Defective input speed sensor
> Defective output speed sensor
> Defective connections or wiring between either speed sensor and the PCM
> Shorted speed sensor circuit
> Open speed sensor circuit
> Slipping clutches inside the transmission

Please note that Transmission Control Module (TCM) replacement WILL NOT correct for this code.

The speed sensor data must be monitored with the proper equipment and the speed sensor circuits must be verified for proper function to determine the actual cause of this fault.

Dec 04, 2011 | 1996 Plymouth Grand Voyager

1 Answer

Trans code po 715 for 1998 dodge grand caravan


Hi
P0715 is for the transmission input speed sensor. This sensor is used for shifting control. It's mounted on the front of the trans, threaded in just under where the cooler lines meet the trans. It has a two wire electrical connector, and a 1" hex for a socket for removal.

This code could be caused by the sensor's wiring, but it's very likely to be the sensor itself and it will need to be replaced. This isn't an uncommon failure.

The input speed sensor runs less than $20 at a parts store and will be in stock at any parts store or dealer. It only takes a few minutes to replace.

Jul 15, 2010 | 1998 Dodge Grand Caravan

1 Answer

Check engine light with following codes p 1529 p0720 p0715


P1529 indicates that your TCM asked the ECM to turn on the check engine lamp.

The range switch and the output speed sensors are the items that are abnormally affecting the operation of the transmission. The diagnostic logic in your computer can distinguish these issues from one another, so you'll definitely want to do both. You have no diagnostic code for the input speed sensor (P0715) listed, so I have made no recommendation to replace it. In my opinion, it's not a labor-intensive repair, so I wouldn't recommend replacing it unless you have reason to believe it's bad.

DTC - P0720 (OUTPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0720 Output shaft speed sensor system
If the output from the output shaft speed sensor is continuously 50% lower than the vehicle speed for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open circuit or short-circuit in the output shaft speed sensor and diagnostic trouble code No. P0720 is output. If diagnostic trouble code No. P0720 is output four times, the transmission is locked into 3rd gear or 2rid gear as a fail-safe measure.
Probable cause
Malfunction of the output shaft speed sensor
Malfunction of the transfer drive gear or driven gear
Malfunction of connector
Malfunction of the TCM

DTC - P0715 (INPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0715 input shaft speed sensor system
If no output pulse is detected from the input shaft speed sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h (19 mph) or more, it is judged to be an open circuit or short-circuit in the input shaft speed sensor and diagnostic trouble code No. P0715 is output. If diagnostic trouble code P0715 is output four times, the transaxle is locked into 3rd gear or 2nd gear as a fail-safe measure.
Probable cause
Malfunction of the input shaft speed sensor
Malfunction of the underdrive clutch retainer
Malfunction of connector
Malfunction of the TCM

Is needed replace.

Nov 04, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
2010 Ford Mustang Logo

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...