Question about Hyundai Accent

Open Question

How to change a 2003 hyundai accent license plate light?

Nothing

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: How to change the rear lights on a 2003 Buick Century.

yes you will you will have to take side trims and sill panel off get a 10 mm ready and take the bolts out the tail liaghts should come out the license lamps have screws in them and if you looka t them but you should be able to twist bulbs and pull them out / Please rate my response thank you very much

Posted on Jan 30, 2009

Ad
  • 98 Answers

SOURCE: how do you change the license plate light bulb

OK>>> it is very cold here, but nonetheless..I went outside to check on my Oldsmobile for your benefit....On mine (I can't guarantee it is the same for all of the vehicles listed above). If you are looking at the license plate, LOOK UP and you should see the bulb and whatever encasing is there. Mine is in a tube and it is attached with (2) mini bolts that will need to come out first, then it just looks like a simple matter of disconnecting the electrical plug, taking out the old bulb and putting the new one in. I hope this helps someone....

Posted on Feb 23, 2009

  • 2 Answers

SOURCE: Replace license plate light 2005 Hyundai Accent

A slightly better set of instructions might help you. Mine is a 2003 Accent. You have to remove the access panel that covers the lamps and the wiper control. Remove the phillips screws along the bottom of the panel (closest to the floor of the trunk when the lid is closed). Then remove the two screws that hold the brackets onto which the two strings are linked which are used to raise the rear deck slightly when the trunk opens. Next, there is a small cover underneath the rear wiper (about 2 inches square) that you need to carefully pry off using a small flat head screw driver via the indents on the lower side of the plastic cover. Inside you will find a 10mm bolt; use a ratchet to remove the bolt. Next, using a small flat head screw driver, carefully pry the middle section of moulding between the panel you are removing and the molding that covers the top portion of the back glass. There are two clips at the base of each middle moulding piece closest to the panel you are removing. Once those pop free, grab the panel at the bottom and firmly but gently pull away from the car body to pop free the two retaining clips holding the moulding to the car body. Finally, use one hand to grasp the panel from the bottom and the other to help help slide the panel "up" towards the glass (top of the car). The panel's top is flanged, and must slide up and away from the lip on which it sits. With the panel removed, grasp the white socket that holds the bulb and with gentle pressure turn it counter clockwise about 40 degrees and then pull the socket out. The replacement bulb is a type 168. Reverse these instructions to assemble, making sure in the end to push all retaining clips back into place until you hear them "catch" and hold the panel firm;y against the car body so that you do not get vibration noise.

Posted on May 19, 2009

  • 3 Answers

SOURCE: changing license plate lights on 2004 chevrolet

the light can be replaced from the back side of the light housing . go under the back side of bumper under the truck behind lisence plate you will see the where the wire goes to the light . grab the housing not the wires and twist about a half a turn and pull gently. it should come out and then remove the light bulb and replace with new

Posted on Jan 29, 2010

  • 389 Answers

SOURCE: how do you replace the license plate light on a

I can't see what you have but lets check a couple of things. If there is any screws visable on the outside of the lens then remove them. Once the cover is off then you should be able to see the bulb. Take the bulb between your thimb and four finger and push in gently and turn to the right and pull out. You would know the rest from there. If no screws outside then lets look in the trunk. You may have to remove some covering in the general area to see the bulb. Follow above directions. If nothing is there then the last place is under the bumper. Have a look and go from there. Let me know I we fixed it. The Raz

Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

License plate lights not working wiring


Are you measuring 4 volts with the ground on your tester attached to what?The door?The vehicle body?Check the ground on the door/wiring also and the follow the positive wiring back, if you still have to, until you get proper voltage.
OR,grab some power from a tail light and feed the licence plates lights with that,if your ground is good on the door.

Apr 08, 2017 | 2003 Hyundai Santa Fe

2 Answers

What is better then God worse then the devil poor people have it rich people want it and if you eat it you'll die. What am I?


Nothing.
Nothing is better than God, nothing is worse than the devil.
Poor people have nothing, rich people want nothing.
If you eat nothing you'll die.

Sep 09, 2014 | Cars & Trucks

1 Answer

I have a Volvo Xc 70 and when I tired to start it nothing happened none of the lights come on the dashboard and when try to start it nothing turns over


If nothing at all is happening no sounds no lights nothing then I would start at the battery make sure all wires going to and from the battery are tight if there is not a tight connection it will not work proper

May 07, 2014 | Cars & Trucks

1 Answer

I have a 2000 Plymouth neon and have been having some issues. When you put the key in and then it to the ON position the lights, radio, and everything comes on inside the car. But the fuel pump is not...


Dead batteries have enough power to turn on the lights you mentioned but under load (cranking ) there will be nothing. have a load test done on the battery to check for failing cell

Nov 17, 2013 | Cars & Trucks

1 Answer

Hummer 2006 smell gas but nothing drip


usually the top of the fuel tank is rotted out from wet mud sitting on it. The fuel sloshes and soaks the mud via the perforations in the tank.

Mar 24, 2012 | Hummer H3 Cars & Trucks

1 Answer

How do I change the license plate bulbs?


Look under the bumper, you should find the light bulbs in a harness. To release them, twist the bulbs until the are unlocked from the harness. Pull the bulb out and replace it.

Apr 17, 2011 | 2007 Hyundai Accent GS Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...