My car has and IAT engine air temp.
and HVAC
the 2.0L engine has this. and one more hidden inside the MAF
http://www.fixkick.com/engine/20Liter/html/image_12.html
see, it there, it's real name is IAT and they never go bad.
Im not arguing name , but is very important go use them.
The IAT is the USA /ASE/SAE name. (and function for EFI controls.)
so why not post symptoms or state the job.
so we can be on same page.?
are you hacking it? (you will fail, if you do , i promise)
to change it, unplug it. then remove it
reverse above, same with all sensors really
but all connectors are locked, and all FSM on all cars
tell you how to do, (press lock and gently pull)
think this IAT just pulls out. of a rubber grommet.
in some countries, (you never said) the car
has no IAT at all. so...... can help much ,.
my 92 vitara has non then was added in 1993. on up.
in USA.
in some countries other parts are missing to in the EFI system
and uses different spark system.
mine uses COPS others use a single twin coil pack
my point,, no country ,no joy,
SOURCE: cabin filter element location
Filter is located behind the glove box. All you need is a screwdriver to replace.
1. Open the glove box and empty to take the weight off the box.
2. On the right side there is a plastic hinge like device held on by one Phillips head screw. If you have trouble removing with a Phillips screwdriver you can remove with a narrow flat head screwdriver. Remove the screw and slide hinge off the mount.
3. To drop the glove box press the sides slightly inwards while 'forcing' it open beyond it's normal stopping point. Careful as when it releases it will fall wide open and may even fall from its hinged area. Set it aside.
4. Behind the glove box there is probably some fiberous material inserted to prevent noise like squeaking when it rubs. It is sticky on one side to hold it in place. Just remove and place out of the way.
5. Behind the fiberous material there'll be a cover which kinda looks like a grille. Mine was white and it is in the center of the opening. Remove it by releasing the clips at the left or right. It comes right out.
6. When the cover comes off slide the filter out and replace it. The filter lays flat and just slides in and out easily. However, if it has been some time since you replaced be prepared for a lot of debris on top of the filter such as leaves, grass or other general type of debris that has been sucked into the filter. It also may be the source of any bad odors that you smell through the air conditioning system.
7. Reverse the process. Replace the cover and push the glove box lid back into place. When you replace the glove box be careful to make sure the hinge you initiallly removed the screw from is not left behind the glove box or you will have to remove again to get it out. Replace the screw and do not over tighten as it screws into plastic and then your done.
SOURCE: suzuki grand vitara 2006 CHANGING REAR BULB
Just unscrew the screw, then pull hard on the light...it will pop off.
SOURCE: Where is the Mass Air Flow Sensor located on the
Its better to buy the manual book if you want to do it your self, its only $20.00 dude ok
SOURCE: How to change the fuel filter on a suzuki grand Vitara
Fuel FIlter - Removal
To install:
Negative battery cable
Fuel lines from the fuel filter
Fuel filter
Fuel filter and tighten the bracket bolt. Note the fuel flow
directional arrow.
Fuel lines to the fuel filter.
Negative battery cable
To install:
Negative battery cable
Fuel lines from the fuel filter
Fuel filter
Fuel filter is incorporated in fuel pump assembly in fuel tank.
Fuel filter and tighten the bracket bolt. Note the fuel flow
directional arrow.
Fuel lines to the fuel filter.
Negative battery cable
Hope this help.
SOURCE: Replaced the battery in my 2006 Suzuki Grand
My wife left the ignition on with the lights on and drained the battery completely. I'm having the exact same problem. Any ideas how to fix it?
160 views
Usually answered in minutes!
×