I GOT A CODE ON MY CHEVY EQUINOX CODE IS P0011

https://www.carparts.com/blog/p0011-code-a-camshaft-timing-over-advanced-bank-1/

https://www.google.com/search?q=Nissan+P0011


P0011 Nissan See the error code p0011. it indicates the engine control module has determined that the bank 1 intake camshaft is more advanced than what the engine control module has commanded it to be. Jul 23, 2021

How to Fix NISSAN P0011 Engine Code in 4 Minutes [1 DIY ...

https://www.youtube.com/watch?v=mQefsbHzCYc

Watch this

You can read all about your code here:
http://www.obd-codes.com/p0011

Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

As you know one of the problems can be the Fuel Cap. I make this suggestion. If you changed your Fuel Cap before the Purge Valve double check that the cap used was an OEM (Original) Chevy Part for that specific vehicle, not just any cap from another Chevy.

You need 2 replace a part called the magnet it advances the crank shaft get it from the dealer

bank 1 intake sensor fault, I would disconnet wire at sensor with key off and look at terminals closely to see if the female terminals are tight together so as to when they are plugged into sensor (male spades) are tight in connector, and not partially backed out. bank 1 is the head that is the farthest forward on eng. (pass. side) and intake sensor would be the inner sensor....there are 4 of them...2 exhaust and 2 intake . each head has 1 exh. and 1 int. sensor. good luck hopefully you just have a bad connection !

Potential Symptoms

Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
Causes

A P0011 DTC trouble code may be caused by one or more of the following:

• Incorrect camshaft timing
• Wiring problems (harness/wiring) in intake timing control valve control solenoid system
• Continuous oil flow to VCT piston chamber
• Failed timing valve control solenoid (stuck open)

Possible Solutions

This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.
A P0011 DTC trouble code may be caused by one or more of the following:

• Incorrect camshaft timing
• Wiring problems (harness/wiring) in intake timing control valve control solenoid system
• Continuous oil flow to VCT piston chamber
• Failed timing valve control solenoid (stuck open)

This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.
Thank you for using fixya