2003 Sebring - no power - won't start

The keyless entry system consists of the following components:

• driver door module (DDM)
• keyless entry transmitter
• keyless entry keypad

The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).

• Battery junction box (BJB) fuses:
  • circuit breaker 7 (20A)
• Central junction box (CJB)
  • 4 (10A)
  • 6 (15A)
  • 8 (25A)
  • 13 (5A)
• Keyless entry keypad switch
• Power door lock actuator
• Luggage compartment release switch
• Luggage compartment release solenoid
• Connectors or connections
• Wiring harness
• If fuse's good have checked for DTC'S - diagnostic trouble codes .
• B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .

• The doors do not lock/unlock using the remote transmitter

• Remote transmitter not programmed.
• Remote transmitter.
• DDM.

• Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.

1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.

1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.

1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

how old is the battery?

KEY WORDS to search for are
2003+VOLKSWAGEN+remote+receiver...

or "keyless+module"

I only got hits back from eBay (& AMAZON)...
which would indicate this is a fairly ROBUST part...
(TYPICALLY: really popular parts = high failure rate).
((in my opinion))


No direct (part number) hits...!!


Look here... Appears to be inside the center console
(surmised without proper documentation)

Looks like
VW VOLKSWAGEN OEM Phaeton Keyless Entry Receiver for Key Fob Remote...

also...
VW VOLKSWAGEN OEM Phaeton Keyless Entry Receiver for Key Fob Remote...

Possibly AMAZON... (use your own module number)
EXAMPLE
Amazon com 2003 jetta keyless module

Hope I am helping...

Carnac the Magnificent

you must to restart your car alarm

sometimes turning the ignition on 3 times quickly without starting will reset the computer. If the van has power locks and keyless entry then try using only the keyless entry. Sometimes your car wont have a alarm but an anti theft device which will not allow it to start if it goes off or something triggers it.

If you (hopefully) have the key fob (keyless entry remote), try closing the doors, then lock and unlock using the keyless entry. This should reset the security so the vehicle will start.

take and have computer scanned for codes

Unfortunately, the keyless entry remotes and OE systems usually require a dealership to service them. Sounds to me like they need to re-set the alarm

my power locks dont work or heated seats on my 2003 Dodge Ram 1500 i also have keyless remote entry and that dont work i took it to the dodge dealer and they had it for three days and could not find the problem they said the called dodge and did not get a answer please help 93300D6B-4D4D-9E7E-99D8-25B4690C888B 1.03.01

" turn the key on engine off 8 times. the doors will lock and unlock. push one of the buttons on the key fob and the doors will lock and unlock. do this for each remote that you have. when you are done turn the key off. the door locks will lock and unlock. the remote fob should work after this."
From My SecuriLock..