Why is open circuit being displayed on my navigatinon computer. on my 2000 jeep grand cherokee limited.

SOURCE: Jeep Cherokee Limited

As you are turning the tailgate is flexing.
If you adjust the striker to get the tailgate to close tighter, it should fix your problem.

Mike Butler

• 6674 Answers
• Posted on Jan 01, 2009

SOURCE: 2004 jeep grand cherokee limited makes a noise

Sounds like a loose belt, Depending on what engine etc., it may need to be changed or if you have adjustment, tightened. When adjustment or replacement done, is a good time to check all pulleys. If your not up to it, an adjustment should not cost too much, few minutes work in most cases, if belt needs changing, price of belt & a little more labor involved.

SOURCE: 2000 jeep grand cherokee limited starts in 3rd gear

oil pressure problem should be checked independently of other problems...Use a good accurate mechanical gauge to check. If pressure is good (no less than 15psi at idle hot (I prefer to see at least 20) check dash grounding, block ground and if OK, change sending unit. Dash and body ground can influence operation of shift and body control modules so indirectly your problem may or may not be related, depending upon what you find while testing. And it could turn out to be a defective module! They are expensive and just plugging new ones in may work, but then again, it might not. I might be totally incorrect on this...that's the value of actually being there instead of doing this by "remote control".
If you read the numerous posts pertaining to all vehicles, you will see that you are not alone with electrical problems...As long as the engineers who design this stuff, keep using "modules" to replace ordinary simple and reliable systems, we will continue to have these problems. Do some testing and I'm sure you will find a solution! (I'm still waiting for someone to make a program for a PC that will give a complete readout of every system in a vehicle, including exact faults instead of general system "suggestions")
Good luck

SOURCE: Jeep Grand Cherokee Limited P0700 diagnostic problem

P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

1. Disconnect battery. This must be done to prevent accidental airbag deployment.
2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
3. Remove the shift knob by pulling sharply upward.
4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
10. Remove the "A" post trim panels.
11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
12. Disconnect the park lamp switch.
13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
18. Unplug the antenna cable near the right cowl side panel.
19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
20. Remove the bolts that secure the instrument panel armature to the windshield fence.
21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
29. Remove the coolant overflow bottle.
30. Remove the Powertrain Control Module with connectors intact and set aside.
31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
32. Remove the heater A/C housing from the vehicle.
33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)