Question about 1996 Jeep Grand Cherokee

1 Answer

1996 jeep grand Cherokee V8 radiator

Remove radiator rom 1996 jeep grand cherokee

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

This is covered by the FSM, and is obvious, an mostly like all cars made. drain it, unbolt it... bla bla.
click, ZJ
then click cooling
and read page 35
any questions?

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Posted on Oct 08, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 512 Answers

SOURCE: 1996 jeep grand cherokee 4 x 4 with 5.2 liter v8

under the vehicle...mounted close to the front of the fuel tank...be sure to release the fuel pressure before you disconnect any line..you can do that by removing the fuel pump relay and cranking the engine

Posted on Sep 27, 2008

Anonymous

  • 74 Answers

SOURCE: The interior lights for my 1996 jeep grand Cherokee Laredo

Hello and welcome to FixYa
The interior lights wont turn off cant because it can't get a conncetion definitely a headlight switch issue common problem for that make
Part # 05137535AA Headlight Switch Probably a dealer item very simple to change this yourself. Hope this gets you going.Please Rate Me. And you can always Ask Me.
1ak+f4pj7cbm32cuniyi2gaaaaaelftksuqmcc

Posted on Apr 27, 2009

Anonymous

  • 52 Answers

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Aug 11, 2009

Richard Scordino

  • 6982 Answers

SOURCE: Where is the camshaft sensor located on my 99 Jeep Grand Cherokee

If you still have a cap rotor and ignition wires, it's inside the distributor. If not, it is the part where the distributor used to be (center rear of the engine behind the intake manifold)

Posted on Feb 19, 2010

emissionwiz

Marvin

  • 85206 Answers

SOURCE: location of cam sensor 2003 jeep grand cherokee v8

Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Posted on Jul 21, 2010

Testimonial: "that is just what i needed thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Radiator change 1994 cherokee


    images for Radiator change 1994 cherokee


    More images for Radiator change 1994 cherokee

    Radiator. Replacement - Jeep Cherokee Forum

    www.cherokeeforum.com > Technical Discussion > OEM Cherokee Tech
    Nov 2, 2010 - Jeep Cherokee XJ 1984 to 1996 How to Replace Radiator .... 1994 JeepCherokee 4x4 5 speed 4.0 H.O. flex headers, Flowmaster cat back, ... Changing out lower radiator hose...
    Jul 6, 2011
    Replacing Radiator
    Apr 8, 2011
    RAdiator removal question
    Feb 19, 2011
    Replacing radiator on 1996 Cherokee
    May 19, 2010
    More results from www.cherokeeforum.com

    93 jeep grand cherokee(4.0) radiator needs to be replaced ...

    www.jeepforum.com > ... > ZJ Grand Cherokee Forum

    Sep 23, 2007 - 12 posts - ‎9 authors
    Remove the top radiator bracket and the whole thing will slide out. IF you have .... What I Have: 1994 Grand Cherokee Limited 2.25" 4 Wheel ...

Jan 23, 2016 | 1994 Jeep Grand Cherokee

1 Answer

How do i remove radiator from my 2002 jeep grand cherokee overland 4.7 ho v8


On older jeeps, the upper radiator support is held by torx screws, T30, if I recall, but maybe T27.
Drain radiator, remove upper and lower hoses, disconnect transmission cooler lines, remove upper radiator support panel, and hood latch if necessary. Check for obstructions-radiator should be free to lift out. Funny that the radiator support and hood latch were both held by torx screws, but were different sizes.

Jul 07, 2013 | 2002 Jeep Grand Cherokee

1 Answer

What type radiator clip or slot fits 1996 jeep grand cherokee v8 4wd


a jeep and a ram truck around the same year should be close.

Jan 24, 2012 | 1996 Jeep Grand Cherokee

1 Answer

Spark plug gap for 1996 jeep cherokee


Thread Grand Cherokke, but ask about Cherokee ???

Make: JEEP
Model: GRAND CHEROKEE - LIMITED
Year: 1996
Engine: V8 - 5.2L - FI - - GAS
Part Number RC12YC
GAP .035" (Original Equipment Manufacturer and/or Original Equipment Equivalent)

Engine: L6 - 4.0L - FI - - GAS
Part Number RC12YC
GAP .035" (Original Equipment Manufacturer and/or Original Equipment Equivalent)


Make:
JEEP
Model: CHEROKEE
Year: 1996
Engine: L6 - 4.0L - FI - - GAS
Part Number RC12LYC
GAP .035" (Original Equipment Manufacturer and/or Original Equipment Equivalent)


Hope this helps (remember to rate this free answer ans leave some testimonial).

Sep 27, 2011 | 1997 Jeep Grand Cherokee

1 Answer

I'm trying to locate the thermostat on my 2000 jeep grand cherokee


  1. On 2000 Jeep Grand Cherokee 4.7L V8
  2. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  3. Remove thermostat housing mounting bolts, thermostat housing and thermostat.

2000 Jeep Grand Cherokee 4.0l v6
Note:on the In-line 6 4.0L model the thermostat housing is mounted at the top of the engine block next to the water pump.

Nov 14, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Needs new radiator, can you put a 2000 radiator in a 2004 jeep grand cherokee


I want to say yes compare the sizes and the water inlets and outlets to determine if it does. I am sure it will.

Sep 25, 2009 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...