I want to install a radar detector in my car using the mirror wiring in my 09 impala ltz to power it. 1) how do i remove the harness from the back of the mirror? 2) which circuits do i plug the wires into? I need a ground wire and a regular switch wire.

You will need to splice the wires as it will be hard to find the right connector to attach to the harness wires. Use the wiring diagram for the car (get it at Alldatadiy.com) and the one that came with the Dual unit to figure out which wires connect to each other.

The seat is held in place with 4 bolts attached to the floor. remove the bolts and disconnect any wiring harnesses that may be attached to seat underside and the seat will remove

Usually your cigarette lighter is what is used to power the radar detector. If you want to add a 12 volt power port then you will need a multitester and check for a hot fuse on your fuse box that is not hot when the ignition is off, and wire your 12 volt power source into that.

Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

1. Verify that the multifunction turn signal lever is in the center of the OFF position.
2. Disconnect the negative battery cable.
3. Disable the SIR system.
4. Remove the steering wheel.
5. Remove the steering column trim cover.
6. Remove the steering column knee bolster.
7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
8. Remove the 2 wire harness straps from the steering column wire harness (1).
9. Remove the steering column bulkhead connector from the vehicle wire harness.
10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.

1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
2. Remove the multifunction turn signal lever (2) from the steering column.

Installation Procedure

1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
2. Verify that the electrical contact rests on the canceling cam.

Notice: Refer to Fastener Notice in Service Precaution.

1. Install the retaining bolts to the multifunction turn signal lever.

• Tighten the retaining bolts to 7 Nm (62 inch lbs.) .

1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
2. Connect the steering column bulkhead connector to the vehicle wire harness.
3. Install the two wire harness straps to the steering column wire harness (1).
4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
5. Install the steering column knee bolster.
6. Install the steering column trim cover.
7. Verify that the lever is in the center or the OFF position.
8. Install the steering wheel to the steering column.
9. Enable the SIR system.
10. Connect the negative battery cable.

I hope this helps you.

Thanks

Hello, to replace the rear mirror, try the following:

1. Roll the passenger side door window all the way down. Turn off the ignition and remove the keys.


2. Gently pry the window control panel from the arm rest with the pry tool or screwdriver starting at the bottom of the panel. Flip it over and unplug all the wire harness outlets from it. Set the panel aside.

3. Locate and remove the two panel door plugs near the arm rest concealing the two screws and remove the screws with the Phillips head screwdriver.

4. Remove the door panel retainer plugs along the edge of the door by pressing in the middle of the plug to unlock it and removing the plug.


5. Detach the mounting triangle from the upper inside door panel covering the side-view mirror.

6. Remove the door panel by lifting outward and then upward. Disconnect the speaker wire harness from the underside of the door panel and set the door panel aside.

7. Locate and disconnect the mirror wire harness.

8. Pull back the foam insulation from the inside panel covering the side-view mirror.

9. Unscrew the three mounting nuts from the mirror using the ratchet, extension and a socket. Do not drop the nuts into the door cavity.

10. Pry the mirror gently away from the outside of the door.

11. Install the new mirror and replace the mounting nuts on the mirror studs and tighten with the ratchet, socket, and extension. Plug the mirror wire harness back in. Replace the foam insulation. Replace the mounting triangle.


12. Replace the door panel by reversing the procedure. Start by plugging in the speaker wire first.


Thanks

Inside drivers door, just opposite of mirror there is a triangular piece of trim with one screw holding it. Remove this and foam padding and you will see the retaining nuts holding the mirror on. Remove these and unplug wire harness. Installation is the opposite

po455 is Probable Cause[s]

1. Defective, loose or missing fuel cap
2. EVAP canister broke, hose cracked or not connected
3. Purge or vent solenoid defective
4 . Vacuum leak at engine po121 code po121 means Throttle Position Sensor/Switch A Circuit Range/Performance Problem . it is usually indicative of a faulty throttle position sensor or faulty wiring harness in the engine bay.

1) Disconnect and isolate the battery negative cable.
(2) Remove the trim panel from the front door.
(3) Disconnect the power mirror wire harness connector from the door wire harness connector.
(4) Remove the mirror flag seal from the inner door panel.
(5) Remove the three nuts that secure the power mirror mounting studs to the door flag.
(6) Remove the power mirror from the outside of the door.

There are a twisted pair of Yellow and Purple wires in the BIG harness by the left side airbox, you need to open the loom and hunt for them

SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the upper speaker.
   1. Disconnect the electrical connector.
   1. Remove the bolts.
   1. Remove the speaker.

1. Position the watershield aside.

1. Remove the exterior rear view mirror access panel.

1. Disconnect the exterior rear view mirror electrical connectors.
   • Release the wiring harness locator.

1. Remove the exterior rear view mirror.
   • Remove the bolts.
   • Feed the wiring harness through the door opening.