2006 Suzuki Forenza Logo

Related Topics:

A
Anonymous Posted on Oct 04, 2014

What is the location of a breather pipe diaphgram on a2006 suzuki forenza engine.

1 Answer

_-__-___-_

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Suzuki Master 20,706 Answers
  • Posted on Oct 06, 2014
_-__-___-_
Suzuki Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Apr 06, 2013
Answers
20706
Questions
2
Helped
6805063
Points
57965

In the usa?
be the first ever to post the country
be the near first with engine size.
all you posted is a body shell and no engine breather are on shells.


if in usa/ , look up, see that hood sticker, for vacuum hoses
it shows the PCV system (old school breather)
post engine size . gas or diesel.

5 Related Answers

Anonymous

  • 8619 Answers
  • Posted on Jan 29, 2009

SOURCE: White Smoke From Tail Pipe/Exhaust

It often means that you are burning antifreeze. You asked if it needs antifreeze, have you noticed any leaking out of the reservoir tank while you are running it? Sometimes when the head gasket goes it will produce a passage for the antifreeze to pass from the capillaries into the combustion chamber. It is easy to check if you have an air compressor. Remove one of the rear sparkplugs and the radiator cap. Fill the radiator and then push some air into the sparkplug hole (get a good seal in case a valve is open). Repeat with all the cylinders and watch for air bubbles coming up into the radiator. If bubbles come up or fluid is pumped out, the head gasket is blown and must be replaced. It is more likely to happen at the back of the engine because it is farthest away from the fan and therefore gets less cooling. Also check your oil for discoloration. If it is a brownish color it could mean your oil and antifreeze are mixing and has the potential to damage your bearings

Ad

Anonymous

  • 22 Answers
  • Posted on Oct 11, 2009

SOURCE: how to change the transmission fulid on a suzuki forenza

there is no dip stic on the forenza no need to go to the dealer and pay for it simply jack the entire car off the ground enough to get yourself under it make sure u support it with appropriate stands. you can check the fluid by removing the plug from the side of the trans u will need a special tool for this u can get from an auto parts store after removing the plug check to make sure the fluid is right to the brim of the plug hole then turn the car on and shift through the gears R,D,1,2,4 and then back again hold in each gear for about 5 sec then turn the car off crawl back under and check again . if low add a little at a time until its filled u can get a small hand pump with a tube on it from auto store u put this in a quart of trans fluid makes the job alot easier . as for the other problem it is you Trans range sensor $65 dollars from the dealer or $45 from OEMsuzukiparts.com not very hard to change Hope this helps

johnjohn2

Johnny Brown

  • 5763 Answers
  • Posted on Nov 28, 2009

SOURCE: on my 2007 suzuki forenza the check engine light

no such code on that car, auto zone uses global testing which pulls universal codes, so that code means someting different for the suzuki, need to have it checked by the dealer or a shop that has import software, or post the code # and i can translate it into import code, good luck.

Anonymous

  • 29 Answers
  • Posted on Jan 28, 2010

SOURCE: Where is the transmission range sensor for 2006

Right on the transmission, to the right side of the engine bay as you are looking down on it. It is a black plastic part that is bolted on the transmission with two 10mm bolts, and connected to the transmission with rod and clip. It is partially obstructed by the radiator hose, but otherwise really easy to get to.

Anonymous

  • 1168 Answers
  • Posted on Nov 16, 2010

SOURCE: Where is the crankshaft position

Hello Aldozer.

It is mounted below the power steering pump and behind the AC compressor(if equipped).
Both will need to be removed to access it.
Here is a pic of the engine after they are removed.
kiltylake_8.gif

I hope this helps you towards a good repair.
Thank you for using FixYa.

KL

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2005 Suzuki Forenza. Heater core from pipe to water pump hose.

now to remove a pipe to hose at core can be hard.
we cut them off, with sharp knife there so we DO NOT damage the core tube (nobody want to remove the whole dash ,doing this wrong)
I cut them off and replace with new.
any mech knows this so have them do it.
heater cores are very fragile. do not forget this.
0helpful
1answer

Camshaft position sensor location on a 2005 Suzuki Forenza

Hello Rod, your Camshaft position sensor will be located on the engine, usually around the accessory drive pulleys. Your local Auto parts retailer will be able to provide a accurate drawing detailing the location and wiring colors.
0helpful
1answer

Relay for cooling fan on 2009 suzuki forenza

USA answers.. all.
which of the 6 engine you have?
we cant guess them. you must say
open hood, look up , see that EPA sticker there,
the engine type and size, is there.
cooling systems are different by ENGINE.

most fan relays are in the fuse boxes. did you look in all fuse boxes
yet>? if not, do so , its marked, read the markings.
0helpful
1answer

How to replace emissions sensor on 2006 suzuki forenza

Oxygen sensor? Which one? On is on the exhaust manifold itself before the catalytic converter. The other is located on the exhaust pipe after the catalytic converter. You will have to get underneath the car to reach it.
0helpful
1answer

Where is transmission located on the forenza suzuki?

Nearly all transmissions are located behind the engine of a vehicle, sort of underneath the dash.
1helpful
1answer

Suzuki forenza 2006 trouble code P0107 What is the probable cause?

P0107....Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

What this means is your engine breather pipe is perished or split or the diaphgram inside the breather is choked up or the split

1helpful
2answers

Check transmission fluid on a 2005 suzuki forenza

I have a 2005 suzuki forenza,where is the transmission dipstick located at under the hood. Thank you!
2helpful
1answer

LOCATION 02 SENSOR BANK 1 SENSOR 1 2006 SUZUKI FORENZA

in the exhaust pipe before the catalytic converter.
0helpful
1answer

Where the tansmission is located at on my 2004 suzuki forenza

its located on the rear of the engine, its bolted to the back of engine,
1helpful
1answer

Need to find out where waterpump of a 2007 suzuki forenza is located

forenza ,its on the front of the engine ,timing belt will need removing to fit it
Not finding what you are looking for?

143 views

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...