<!-- from fixya rte -->How to remove inter door panel 1996 ranger ? - 1996 Ford Ranger SuperCab

How to Replace an Instrument Panel Bulb - YouTube

? 14:56
https://www.youtube.com/watch?v=Rwj74yo2knY
Jun 15, 2013 - Uploaded by Schrodingers Box
Removal of an instrument panel cluster on 1996 Ford Ranger to... 1999 Ford Ranger: How to change dash board lights, walk through part 1 ...

How to Replace Dashboard Lights : Removing ... - YouTube

? 2:42
https://www.youtube.com/watch?v=zzxz7iG81kI
Sep 18, 2008 - Uploaded by expertvillage
Use socket wrench to loosen dashboard bolts. Learn about technique for installing dashboard lights in a 1996 Ford Explorerin this free auto repair series fr. ... do you need to remove the radio bezel to get to the clips?? will this ...

How to Replace Dashboard Lights : Removing ... - YouTube

? 2:30
https://www.youtube.com/watch?v=QJWoJ17liQI
Sep 18, 2008 - Uploaded by expertvillage

it has two straps that hold it up also you have to remove the three screws inside the fuel door to release the filler tube

Explorer/Mountaineer and 1993-99 Ranger
See Figures 1 and 2

1. Open the window.
2. Unscrew the door lock knob.
3. On Explorer/Mountaineer, remove the 2 screws retaining the trim panel located above the door handle.
4. On Ranger, remove the two screws in the armrest and remove it.

Fig. 1: Exploded view of the front door trim panel

Fig. 2: Exploded view of the Explorer and Mountaineer 4-door rear door trim panel

1. If equipped with manual window crank handles, pull off the handle cover, then remove the attaching screw.
2. Remove the trim cup behind (Explorer/Mountaineer) or around (Ranger) the door handle using a small prying tool. Retention nibs will flex for ease of removal.

1. If equipped with power accessories, use the notch at the lower end of the plate and pry the plate off. Remove the plate from the trim panel and pull the wiring harness from behind the panel. Disconnect the harness from the switches.
2. Remove any retaining screws uncovered by the removed trim pieces.
3. Using a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
4. Lift slightly to disengage the panel from the flange at the top of the door
   

1. Disconnect the door courtesy lamp and remove the panel completely. Replace any damaged or bent attaching clips.
2. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

You disconnect the lever linkage, it pulls out of the hole after turning the plastic retainer 90 degrees. Then, remove the 2 10mm nuts from the lever... and reverse the procedure to install the new lever/handle.

remove interior door panel(need special tool to pop plastic clips holding panel to door)with panel off remove plastic film,with window up you should be able to see two 10m nuts-bolts to remove-also have to pop lever off that goes down to door latch

make sure you remove all door panel screws, you can use a mehanics rag to go behind door handle to remove horse shoe clip that holds door handle if you don't have the proper door tools , it is much easier with the correct tools you can buy they are cheap at autozone or kragens, sears... disconnect any door swtiches like door locks , power mirriors if equipped, then just pull up and out on door panel noting the plastic retainers on back of door panels... please rate help, thanks...

The handle is removed by pulling the panel inside the tailgate, just below the top of it...it's held on by 6 or 8 screws. The latches on the bed itself are held on by torx head bolts, if I'm not mistaken

they are just clipped in, simply pull gently on one of the panel, and you will feel it pop out, you may have a screw or two to remove in the arm rest area.....

the button isnt getting pushed or there is a very bad connection there hope this helps

Remove the door panel and on the inside of the door is a clip or a couple of nuts you'll need to remove. The door handle will fall out.