Question about 1996 Isuzu Rodeo

1 Answer

Isuzu rodeo 1996 3.2L V6. Torque specs for alternator pivot bolt 14 mm and lock bolt 12mm. torque for AC idler pulley lok nut 23 mm

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 280 Answers

Isuzu does not list specific torque values for these fasteners. When this is the case, you are expected to use standard torque values. These can be found on the chart I have linked below. Be advised that bolt sizes go by the diameter of the shaft [round shaft portion] of the bolt or stud, NOT the hex head [socket size] of the bolt or nut. Partially remove the bolts so that you can measure the shaft and obtain the correct torque from the chart. See


https://www.swtc.edu/ag_power/diesel_engines/lecture/metric%20torque%20values.pdf

Posted on Oct 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 2 Answers

SOURCE: what is the 98 isuzu rodeo head bolt torque

joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Posted on Sep 01, 2008

emissionwiz
  • 85206 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

mx5turbo92
  • 545 Answers

SOURCE: i'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.

1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tide belt


okay loosen alternator pivot bolt that is the bottom bolt below the alternator pulley,loosen also top pivot bolt to alternator.then you have long adjuster bolt top upper side alternator you need to loosen adjuster bolt lock nut then tighten the adjuster bolt to get alternator belt tight.new belt tension should be 170 - 180 ft lbs, used drive belt tension is 95 - 135 ft lbs, torque adjusting lockbolt 13 ft lbs, pivot bolts to 41 ft lbs.

Sep 01, 2012 | 2002 Lexus RX 300

1 Answer

How do i replace the water pump on a 1997 rodeo v6?


YOU HAVE TO REMOVE TIMING BELT AND IDLER PULLEY.YOU NEED TO REPLACE TIMING BELT WHEN YOU REPLACE WATER PUMP.TO REPLACE WATER PUMP. DRAIN COOLANT SYSTEM.REMOVE UPPER RADIATOR HOSE.REMOVE TIMING BELT AND IDLER PULLEY.UNBOLT AND REMOVE THE WATER PUMP.CLEAN ANY GASKET MATERIAL OR SEALANT RESIDUE FROM THE WATER PUMP MATING SEALING SURFACES.WHEN INSTALLING NEW WATER PUMP BESURE TO USE A SEALANT ON BOTH SIDES OF WATER PUMP GASKET TO KEEP IT FROM LEAKING COOLANT.TORQUE WATER PUMP BOLTS TO 13 FT LBS IN A TWO STEP CRISSCROSS SEQUENCE.INSTALL THE IDLER PULLEY.TIGHTEN THE MOUNTING BOLT TO 31 FT LBS.INSTALL AND TENSION THE TIMING BELT.INSTALL THE UPPER RADIATOR HOSE.REFILL BLEED THE COOLANT SYSTEM.

Feb 19, 2011 | 1997 Isuzu Rodeo

2 Answers

Head Bolt torque settings for a 3.1 bighorn turbo Deisel


What is the torque for the crank pulley for 3.1turbo

Dec 21, 2010 | 1996 Isuzu Trooper

4 Answers

How to remove alternator on a 2005 range rover


Hi
Click here

the link above should tell you all you need to know if you get stuck or have any problems give me a shout back ok

Oct 26, 2010 | Land Rover Range Rover Cars & Trucks

1 Answer

V6 T3000 need torque specs has throttle body injector


3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

Aug 15, 2010 | 1994 Mitsubishi Montero

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

1 Answer

How to change head gasket?on gas v6. ISUZU RODEO Vin #452CG58V554341786


This is the same for many years. I will send this in 2 post it is to long. Hope this helps you. From the '00 Rodeo workshop manual:

Cylinder Head Assembly
Removal
1. Disconnect battery ground cable.
2. Disconnect connector of intake air temperature
sensor from intake air duct.
3. Remove PCV hose from air intake duct.
4. Remove nut from air intake duct bracket and loosen
hose clamp on throttle body. Remove air intake duct
assembly with air cleaner cover.
5. Remove intake air duct bracket from cylinder head.
6. Drain engine coolant.
7. Move drive belt tensioner to loose side using wrench
then remove drive belt.
033RW001
8. Remove radiator upper hose from engine side.
9. Remove four nuts of exhaust front pipe.
10. Remove three bolts from generator bracket then
remove the generator with brackets.
065RW025
11. Disconnect crankshaft angle sensor connector.
12. Disconnect knock sensor connector.
13. Remove heater hose from adapter side.
14. Remove heater hose from water pipe side.
15. Remove water hose between water pipe and throttle
body.
16. Remove fuel pipe joint eye bolts from fuel rail
assembly and remove fuel pipe bracket with electric
ground cable.
042RW001
17. Disconnect connector for evaporation valve.
18. Remove canister hose.
19. Remove fixing nut of intake manifold stay from
cylinder block side.
025RW002
20. Remove two bolts from intake manifold for water pipe
support and remove cylinder head assembly.
21. Remove engine harness cover and disconnect three
connectors from chassis harness on left rear side
engine compartment.
22. Disconnect connector for power steering pump
pressure switch.
23. Remove four bolts and remove crankshaft pulley.
ENGINE MECHANICAL (X22SE 2.2L) 6A–23
020RW014
24. Remove two bolts and nut then remove timing belt
front cover.
25. Remove ventilation hose from cylinder block side and
from cylinder head side.
26. Remove two bolts, ignition cable cover and remove
ignition cables from spark plug.
27. Disconnect camshaft angle sensor connector.
28. Remove ten bolts and remove cylinder head cover.
29. Remove fixing bolt of timing belt tensioner then
remove timing belt tensioner.
020RW010
30. Remove timing belt.
CAUTION:
 Do not bend or twist belt, otherwise its core could
be damaged. The belt should not be bent at a
radius less than 30 mm.
 Timing belt drive gear counterhold with J–42620.
 Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
 Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
 Store timing belt in cool and dark place. Never
expose the belt direct sunlight or heat.
31. Remove two idle pulleys, the left side with idle pulley
bracket.
32. Remove two bolts and stud bolt and remove timing
belt rear cover.
33. Remove camshaft angle sensor
34. Disconnect engine oil pressure switch connector.
050RW005
35. Remove camshaft assembly exhaust side.
36. Use J–42623 to remove ten cylinder head fixing bolts
012RW007
6A–24 ENGINE MECHANICAL (X22SE 2.2L)
Installation
1. Put cylinder head gasket on the cylinder block.
012RW011
2. Install the cylinder head assembly, tighten cylinder
head bolts by four steps tightening method in the
following sequence to the specified torque.(use
J–42623)
Torque: 25 N·m (18 lb ft) + 90 + 90 + 90
012RW006
3. Install camshaft assembly exhaust side and tighten
camshaft bracket bolts in the sequence to the
specified torque.
Torque: 8 N·m (5.9 lb ft)
015RW014
4. Connect engine oil pressure switch connector.
5. Install camshaft angle sensor.
6. Install the timing belt rear cover and tighten three
bolts to the specified torque.
Torque
M6 bolt: 6 N·m (4.4 lb ft)
M8 bolt: 8 N·m (5.8 lb ft)
020RW012
7. Install left side idle pulley with idle pulley bracket,
tighten to the specified torque and install right side
idle pulley and tighten to the specified torque.
Torque: 25 N·m (18 lb ft)
ENGINE MECHANICAL (X22SE 2.2L) 6A–25
020RW016

Oct 09, 2009 | Isuzu Rodeo Cars & Trucks

2 Answers

Change idler pulley


It's a T-40 size, but I removed the bolt by first removing the bracket holding the pulley--I assume you're talking about the alternator idler pulley, the one right below the alternator. The bracket is held in place by three 14 mm bolts which I was able to reach from the top of the engine (after removing the black plastic air tube). I then put the bracket in a vise and "buzzed" off the 14 mm nut using an electric impact wrench ($30 +/- from Heartland of America). Be careful when putting the nut back on--the impact wrench will likely be too much torque!


May 17, 2009 | 2003 Kia Sedona

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

1 Answer

Timing belt slak


  1. Set timing belt tensioner.
(a) Using a press, slowly press in the push rod using 100 - 1000 kg (220 - 2,205 lb, 981 - 9,807 N) of pressure. (b) Align the holes of the push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod. (c) Release the press.
  1. Install timing belt tensioner.


(a) Turn the No.1 idler pulley bolt counterclockwise to obtain the specified torque toward the left as far as the No.1 idler pulley will go, and temporarily install the tensioner with the two bolts Torque: 18 N.m (180 kgf.cm, 13 ft.lbf)


NOTICE: To apply the correct torque, apply the torque wrench along the axis through the bolts of the No.1 idler pulley and exhaust camshaft timing pulley.


(b) Slowly turn the crankshaft pulley 5/6 revolution, and align its groove with the ATDC 60° mark of the No.1 timing belt cover.
NOTICE: Always turn the crankshaft clockwise.





(c) Insert a 1.90 mm (0.075 in.) feeler gauge between the tensioner body and No.1 idler pulley stopper.
(d) Turn the No.1 idler pulley bolt counterclockwise to obtain the specified torque.
Torque: 18 N.m (180 kgf.cm, 13 ft.lbf)
NOTICE: To apply the correct torque, apply the torque wrench along the axis through the bolts of the No.1 idler pulley and exhaust camshaft timing pulley.

(e) While pushing the tensioner, alternately tighten the two bolts. Torque: 21 N.m (210 kgf.cm, 15 ft.lbf)



(f) Remove the 1.90 mm (0.075 in.) feeler gauge. (g) Remove the 1.27 mm hexagon wrench from the tensioner.


(h) Slowly turn the crankshaft pulley one revolution, and align its groove with theATDC 60° mark of the No.1 timing belt cover.
NOTICE: Always turn the crankshaft clockwise.




(i) Using a feeler gauge, check the specified clearance between the tensioner body and No.1 idler pulley stopper. If the clearance is not as specified, remove the tensioner and reinstall it.
Clearance: 1.80-2.20 mm (0.071 - 0.087 in.)
  1. Check valve timing.



(a) Slowly turn the crankshaft pulley two revolutions from TDC to TDC. NOTICE: Always turn the crankshaft clockwise.




(b) Check that each pulley aligns with the timing marks as shown in the illustration. If the marks do not align, remove the timing belt and reinstall it.

Nov 12, 2008 | 1993 Toyota Celica

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

469 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...