Toyota echo 2003 ignition switch lock my key goes in the ignition but will not turn

It's either faulty ignition lock or the switch at the bottom of the gear stick which I've had twice before

you need to replace your switch the theft system is activated with the key maybe try putting the key close to where it goes

IGNITION KEY WILL NOT RELEASE

It can be faulty ignition lock cylinder. I suggest to wiggle the steering wheel a bit and see if the key gets released out. If that is not helping then first turn steering wheel to right and try removing the key, or next turn steering wheel to left and see if you can remove the key.

----------

Spray wd-40 in the ignition key hole and let it remain there for few minutes, after that once again try to remove the key and see if that helps.

---------

But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.

-----------

For more troubleshooting on these types of issues, I suggest you to refer the help links mentioned below. Its the accurate solutions mentioned in it. That will help you to narrow the problem: -----

Click the link below: ------

-----------

1999 Toyota Camry: Key Will Not Come Out Of Ignition?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html

---------------

2001 Toyota Tacoma: Ignition Locked?

http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html

------------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

-----------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Ignition Key OFF but engine still running?

http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html

--------------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

-----------

Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html

-------------

Key won't turn in the ignition on Toyota land cruiser?

http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html

-------------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

-----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

Adding key.
Note: You must be having one working master key to perform this function.
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

- Connect the pins 4 (CG) and 13 (TC) with a paper clip or automotive wire, keep open the driver's door and leave the ignition switch ON for 30 minutes.
- After 30 minutes, switch OFF the ignition, remove the jumper wire and start the engine.

It can be faulty ignition lock cylinder.I suggest to wiggle the steering wheel a bit and see if the key gets released out.If that is not helping then first turn steering wheel to right and try removing the key,or next turn steering wheel to left and see if you can remove the key.
----------
Spray wd-40 in the ignition key hole and let it remain there for few minutes,after that once again try to remove the key and see if that helps.
---------
But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.
-----------
For more troubleshooting on these types of issues,i suggest you to refer the help links mentioned below.Its the accurate solutions mentioned in it.that will help you to narrow the problem:-----
Click the link below:------

-----------

1999 Toyota Camry: Key Will Not Come Out Of Ignition?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html
---------------

2001 Toyota Tacoma: Ignition Locked?

http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html
------------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
-----------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Ignition Key OFF but engine still running?

http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html
--------------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html-----------

Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html-------------

Key won't turn in the ignition on Toyota land cruiser?

http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html

-------------------

How to remove ignition switch on VW Car models?
http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html
-------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

-----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html
-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html
------------------These will help.Thanks.

See if you turn the wheel and try to turn the key at the same time if it releases. We might get a free spot where the key should turn. The lock may be in a bind and pressure on it may release it.
Clean and lubricate the lock cylinder. Electric cleaner to flush the dirt and liquid graphite to lubricate. A substitute for the electric cleaner is a spray of isoprophyl alcohol.
You may also need to tap the assembly for the ignition switch to release the mechanical parts. See if you can get the cover of the steering column off to gain access to the ignition switch assembly.
Check also if the spare does the same, other wise the key may have deformed.

your switch is probably bad.. replace the ignition key and cylinder lock.

If you are attempting to install an aftermarket radio Don't butcher the plugs on your Toyota ... simply go to a car stereo shop and buy an adapter plug for $10-$20 then wire it to your new radio ... then just plug them together (the wires on the adapter are marked) You'll likely need a dash kit too ... save yourself from a lot of frustration time and money! ....

check fusible link or faulty wirings!your problem is near the source or supply of the battery...you can do that!trust your self