How change front fender f150 2000

Remove the LH front fender splash shield !
Fender Splash Shield Removal and Installation

1. Loosen the running board bolts and lower the running board to access the front fender moulding pin-type retainer.
   • To install, tighten to 23 Nm (17 lb-ft).

1. Remove the lower pin-type retainer from the front fender moulding.

1. Remove the 2 rear pin-type retainers from the front fender moulding.

1. Position the front fender moulding aside and remove the splash shield lower screw.

>

1. Remove the front splash shield screws.

1. Remove the front splash shield pin-type retainers.

1. Remove the front splash shield.

1. Remove the front fender splash shield.

1. To install, reverse the removal procedure.

the battery is located in front of the drivers side front wheel behind the inner fender well.you will have to remove enough of the inner fender to gain access to the battery to replace it.

Basically you remove the hood, remove front lights, then unbolt the fender from the uni-body. reverse to put the new one on.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

first if you are changing the bulb only and it is a HALOGEN
there is a round acess hole in the inner fender remove it and change the bulb
if you have HID lights or are changing the head light assembly then you have to remove the front bumper facia
hope this helps
hope you have HALOGEN lights

you have to remove the front bumper facia
remove all the push pins under the hood
remove both front wheels
remove both inner fenders
disconnect the fog light harness
3 bolts on each side that hold the front fenders to the facia
the front facia should slide off
then remove the 10mm bolts for the headlight
then reassemble
hope this helps

Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

If you have the small block V8 I think it's the 223 engine, you may have to go in through the inner fender well, jack up the front of the car, remove the tire and then locate the screws that hold the inner fender well in place. Remove the fender well and it shoudl give you access to the plugs.

Can you remove the wheel well splash shield and get access to the bolts? Body shop techs have a special tool to get into this area.

Here's a 97 Probe whcih was the same as a 626 in 1997:

Fender, Front Removal

1. On GT models, remove the side sill extension. Refer to Section 01-08 for the removal and installation procedure.
   

1. Remove the front fender bolt located in the door jamb opening.
   
   
   RH Side Shown, LH Side Similar
   
   
   
   
   

1. Remove the three upper front fender bolts located on top of the front fender (16005) inside the engine compartment.
   

1. Raise and support the vehicle.
   

1. Remove the wheel (1007).
   

1. Remove one push pin and five front fender splash shield bolts and remove the front fender splash shield (16102).
   

1. Remove the upper front fender brace screw.
   

1. Remove the inner front fender bolt.
   

1. Remove the screw holding the front bumper cover (17D957) to the front fender.
   

1. Remove the two lower front fender bolts.
   

1. Remove the front fender.
   

Installation
To install, reverse the removal procedure. Tighten the front fender bolts to 7-9 Nm (61-86 lb-in).

Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

look at the turn signal lens, see if there are screws holding them, if they are, remove the screws and remove the signal light assembly, after removing, you can replace the bulb by removing the socket at the back of the lens assembly.

tnx 4 using fixya,

drcool