Question about 1992 Buick Century

1 Answer

Location of ECM and how to change ECM.

Installing a ECM in a Buick Century.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 1,413 Answers

Passenger side Under dash on the side kick pad with 3 connector
To replace it .. unplug battery then remove connector at ECM on old ecm remove two screw and the plate remove both memory and install them in the new ECM....plug 3 connectors and battery cable

hope it help

Posted on Dec 12, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
c17hydro

Greg Bernett

  • 2989 Answers

SOURCE: flasher out on buick and cannot find location to replace it

Open access panel directly under steering column, pull off flasher unit (metallic cylinder) take to auto parts store (no more than 10 bucks) , put on new one, drive safe.

Good Luck and please don't forget to rate!

Posted on Mar 16, 2009

bunnydawg

Roberta Smith

  • 5158 Answers

SOURCE: Where is the ECM located on an 1989 Buick Century Custom V6 3.3 l

unhook the battery for about 15 minutes... that will reset it ... if the stereo is an anti theft type... make sure you know the code and how to enter it.

Posted on Mar 18, 2009

honeymokey

honeymokey

  • 3113 Answers

SOURCE: location of the starter on the engine

follow the positive + cable from battery to the starter.

Posted on Apr 19, 2009

csmock132

Clint Smock

  • 4669 Answers

SOURCE: 2001 Buick Century shift solenoid

It is in the side cover on the valve body. The transmission needs to be removed to access the solenoids.

Posted on May 18, 2009

Anonymous

  • 240 Answers

SOURCE: 1988 buick century headlights

To change the low beam headlight on the 2001 Lesabre, the headlight assembly must first be removed from the car. It is really quite simple to do. There are two bolts on the top of the assembly that must be removed - that is all! The entire assembly comes out and gives easy access to the low beam bulb. Give it a 1/4 counterclockwise turn to remove it. Plus in the new one (#9006) and reverse the procedure.

Posted on Jun 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE ECM LOCATED


passenger side behind dash , i've copied a schematic , hope fully it will load, also known as a PCM

2002 buick century ecm location Google Search

Apr 10, 2015 | 2002 Buick Century

2 Answers

How to replace ecm on 1993 buick century?


remove knee bolster on the passenger side and find the ecm under the dash behind the glove box. some of these you can remove the inner glove box to give you more room. it is held in a bracket that you will have drop down and unbolt the holding fasteners that hold the ecm in the bracket then disconnect the plug connectors to the ecm.

Aug 05, 2014 | 1993 Buick Century

1 Answer

No power to the fuel pump on a 1996 buick century


check for a problem fuel pressure regulator
most are wired to the ECM which is connected to the relay for the pump
it works like this
with low / no fuel pressure the regulator completes a circuit to the ECM
that signal is then sent to a relay to start the pump
when full pressure is reached , the regulator signals the ECM and the relay is turned off hence the pump is not continually running when pressure is not required

Nov 12, 2017 | 1996 Buick Century

1 Answer

I have a 2001 Buick Century Custom. ABS, Trac and service engine light come on after 45 minutes and stay on. I have replaced left rear main bearing/speed sensor twice and wiring harness with same result....


have they checked the PCM/ECM fuses? some might be bad or the computer itself. does the car run poorly, bad fuel economy? you could go the the emission check place to have it checked. for alot less money it will tell you if it is computer related before spending more for a mechanic to analyse it .$15 in WA State.

Feb 03, 2018 | 2001 Buick Century

2 Answers

Location of the headlight relay for a 2001 buick century


where is the location of the headlamp relay on a 2001 Buick century

Aug 12, 2010 | 2001 Buick Century

1 Answer

Engine hi engine diagnose lite on scantool


ay chek all the ground wires that go to the ecm
chek alterneter and battery
chek ignation module and the knock sensor
every won was good
than ay change the ecm and the problem is over

Jun 20, 2009 | 1993 Buick Century

1 Answer

Caliper pin/bolts location


Top to keep it grease sealed.You never have to take that out if your changing pads.Only when you are changing the caliper

Jun 07, 2009 | 2004 Buick Century

1 Answer

2001 Buick Century shift solenoid


It is in the side cover on the valve body. The transmission needs to be removed to access the solenoids.

May 03, 2009 | 2001 Buick Century

1 Answer

Where is the ECM located on an 1989 Buick Century Custom V6 3.3 l


unhook the battery for about 15 minutes... that will reset it ... if the stereo is an anti theft type... make sure you know the code and how to enter it.

Mar 18, 2009 | 1989 Buick Century

Not finding what you are looking for?
1992 Buick Century Logo

565 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...