Question about 1995 Eagle Summit

1 Answer

95 Eagle Summit 1.8L cam timing marks

95 Eagle Summit 1.8L single overhead cam. I'm replacing the timing belt & I can't find a mark on head to align with the mark on the cam sprocket. Anyone know what to align it with?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 20 Answers

Get a repair manual there must be a mark or reference point of some kind

Posted on Jul 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a picture of the timing marks for Jeep 4.0


Timing the Cam to the Crank

There are several ways to time the cam to the crank. Be sure to check the manual before you install the timing chain or belt.

  • Some timing sprockets are properly timed when the marks face each other.
  • On others, there must be a certain number of chain links between the marks.
  • Sometimes chains have colored links that must be aligned with the marks on the sprockets.
  • Some overhead cams have a mark on the cam gear that lines up with a mark on the cylinder head when the timing mark on the damper is at the TDC mark.
Align the timing marks for the camshaft and crankshaft sprockets before removing the timing belt or chain.

If the old parts are available, carefully compare the new gears or sprockets with the old ones. Check the keyway and timing marks just in case there might have been an error made in manufacturing. Sprockets are sometimes stamped backward. Its much better to find the problem during assembly, rather than waiting until problems show up after reassembly and reinstallation.

Maintaining Valve Timing

During a valve job, it is essential to keep the timing chain or belt in place to maintain correct valve timing. Position the number one cylinder at TDC. Some overhead cam engines use a single long chain for a cam drive. The chain can be wedged against its guides with a tapered block of wood.
the chain tensioner on some ohc engines must be wedged to keep the chain in position during cylinder head removal. courtesy of nissan motors.

Some engines have a lower and upper chain. These engines do not require special attention to wedging the chain. Be sure to look for hidden head bolts and check the repair manual before removing the OHC head.

Dec 07, 2012 | 1989 Jeep Cherokee

1 Answer

I have found the crankshaft marks but I cannot find marks to align the to over head cams on my car, the dohc are run from 1 wheel. I am trying to re-align the timing belt as i think they have gone off.


if it's a dual overhead cam then each head has two cams and two pully's, a single overhead cam engine has one cam and one pulley on each head. if the belt has more than 60,000 miles on it you should replace it. you need to find out if the engine is an interference engine or not to determine the level of damage caused if the belt has jumped or slipped. your overhead cam timing marks are usually on the cam faces and the backing plate behind the cam or sometimes there's two marks on the cam that you align with the surface of the head behind them. the first thing you need is a diagram of the belt routing and mark positions because timing marks are very important especially on an interference engine. starting or cranking an interference engine with the timing marks misaligned can bend all your valves or even punch holes in your pistons! so proper alignment is crucial, good luck.

Jan 02, 2011 | Mazda 323 Cars & Trucks

1 Answer

Hi, I am looking for a timing belt diagram for a 1998 2.5ltr Subaru Outback or can you tell me which timing marks on the sprockets line up to the encasing.


Timing Belt Cover, Belt & Sprockets Removal & Installation 2.5L Engine To Remove:
  1. Remove the drive belts.
  2. Remove the A/C compressor drive belt tensioner. Timing belt & cover DOHC exploded view subaru-03-25-6470.gif

  3. Remove the crankshaft pulley.
  4. Remove the mounting bolts and left timing belt cover.
  5. Remove the mounting bolts and right timing belt cover.
  6. Remove the mounting bolts and front timing belt cover.
  7. Vehicles W/ M/T: Remove the timing belt guide.
  8. Ensure that the timing belt rotation arrows are still visible. If the marks are worn off, place new rotation marks on the belt. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  9. Turn the crankshaft using a breaker bar and special adapter socket on the crankshaft. Align the timing mark on the crankshaft sprocket (1), left intake sprocket (2), left exhaust sprocket (3), right intake sprocket (4) and right exhaust sprocket (5) with the notches in cylinder block and timing belt cover.
  10. Paint alignment marks on the timing belt at the crankshaft and camshaft sprockets timing marks. CAUTION
    Do not turn the camshaft sprockets with the timing belt removed. The valves heads will contact each other causing the valve stems to bend.
  11. Remove the lower right idler pulley.
  12. Remove the timing belt.
  13. Remove the upper right idler pulley.
  14. Remove the lower left (toothed) idler pulley.
  15. Remove the belt tensioner.
  16. Hold the sprocket and remove the left intake and exhaust camshafts.
  17. Hold the sprocket and remove the right intake and exhaust camshafts.
  18. Remove the crankshaft sprocket.
To Install:
  1. Install the crankshaft sprocket.
  2. Hold the sprocket and install the right intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  3. Hold the sprocket and install the left intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  4. Reset the automatic belt tensioner as follows:
    • Remove the mounting bolt and belt tensioner. NOTE: Do not exceed more than 2,205 lb. (9,807 N).
    • Place the belt tensioner on a press. Press the adjuster rod down gradually (using more than 3 minutes) 66- lb (165 N) or more until the adjuster rod is aligned with the stop pin hole in the cylinder.
    • Insert a 0.08 in (2 mm) diameter pin or hex wrench into the pin hole to lock the adjuster rod.
    • Install the automatic belt tension adjuster with the mounting bolt. Tighten 18 ft-lb (25 Nm).
  5. Install the lower left (toothed) idler pulley. Tighten 29 ft-lb (39 Nm).
  6. Install the upper right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm). Crankshaft sprocket and oil pump cover alignment marks 2.5L DOHC subaru-03-25-4890.gif

  7. Align the timing mark on the crankshaft sprocket with the mark on the oil pump cover. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  8. Align the single timing mark on the right exhaust camshaft sprocket with the notch on the timing belt cover.
  9. When the single timing mark on the right exhaust camshaft sprocket is aligned with the notch on the timing belt cover, ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned.
  10. Align the single timing mark on the left exhaust camshaft sprocket with the notch on the timing belt cover by turning the sprocket counter clockwise (viewed from front of engine).
  11. Ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned when the single timing mark on the left exhaust camshaft sprocket is aligned with the notch on the timing belt cover. CAUTION
    • The camshafts can be rotated independently causing the valves heads to contact each other resulting in bent valve stems.
    • When the timing belt is removed the camshafts will turn to the lowest cam lobe position by the force of the valve springs. Before installing the timing belt the 4 camshafts are in the lowest lift position (valves closed).
    • When the camshafts are rotated to install the timing belts, # 2 intake and # 4 exhaust cam lobes of the left camshafts are held to push their corresponding valves down. In this position, these valves are held in the open position. Right camshafts are held so their cam lobes do not push the valves down.
    • The left camshafts must be rotated from the lowest lobe position to the position where the timing belt can be installed at the smallest possible angle in order to prevent intake and exhaust valve contact. Camshaft sprockets rotation subaru-03-25-6473.gif

    • Do not turn the camshafts in the direction shown in the illustration because the valves will open at the same time and contact each other.
    CAUTION
    If the timing belt alignment is off the mark buy more than 3 teeth, the valves and pistons may have contact.
    Timing belt alignment marks DOHC subaru-03-25-6472.gif

  12. Align the timing marks on the belt with the marks on the sprockets in the numerical order shown in the illustration.
  13. Install the lower right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm).
  14. Ensure that the timing mark alignment is correct and remove the tensioner stop pin.
  15. Vehicles W/ M/T: Install the timing belt guide and temporarily tighten the mounting bolts.
  16. Vehicles W/ M/T: Measure the clearance between the guide and timing belt. The clearance should measure 0.039 ± 0.020 in (1.0 ± 0.5 mm).
  17. Vehicles W/ M/T: Tighten the guide bolts 7.2 ft-lb (9.8 Nm).
  18. Install and secure the front timing belt cover with the mounting bolts.
  19. Install and secure the right timing belt cover with the mounting bolts.
  20. Install and secure the left timing belt cover with the mounting bolts.
  21. Install the crankshaft pulley.
  22. Install the A/C compressor drive belt tensioner.
  23. Install the drive belts.
prev.gif next.gif

Sep 30, 2010 | Subaru Outback Cars & Trucks

2 Answers

Timming bailt marks for 1990 plym laser rs


REMOVAL & INSTALLATION 1.8L Engine
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt. Fig. 1: Silent shaft belt timing marks — 1.8L engine 89573g93.gif
    Fig. 2: Checking the silent shafts for proper positioning 89573g94.gif
    Fig. 3: Timing belt timing mark alignment — 1.8L engine 89573g95.gif
    To install:
  7. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  8. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1⁄4 in.
  9. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  10. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  11. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover. NOTE: There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  12. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  13. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  14. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  15. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  16. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  17. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1⁄2 in.
  18. Install the timing belt covers and all related items.
  19. Connect the negative battery cable.

Aug 02, 2010 | 1990 Plymouth Laser

1 Answer

I need a diagram of timing chain replacement Thank You


During most engine rebuilds, a completely new timing assembly should be installed. If wear exists on any component, replacement of the entire assembly is necessary. Wear in the chain, gears, or sprockets means a timing lag, which results in poor engine performance.
The timing chain or belt is generally installed with the gears in their correct positions. Before installing a new chain, soak it in oil.
OHC (Overhead Cam) Engines
Some OHC engines use a chain drive; others use a belt drive. Removing the cover on some OHC engines that have timing chains is more difficult, because the cover often fits between the oil pan and the cylinder head. There are special procedures for replacing cam timing components in these engines.
Before a chain repair job, perform a leakage test on non-freewheeling engines to check for bent valves, so that an accurate repair estimate can be made.
OHV (Overhead Valve) Pushrod Engines
On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another. NOTE THIS IS FOR 2WD 4.0

May 22, 2010 | 2005 Nissan Pathfinder

1 Answer

I'am trying to set the timing for a 96 mit.eclipse


you have to line up all 3 of your tjmjng marks.Is your engine single head or double overhead cams The marks have to line up.Firstyou have to remove the belt.Then remove harmonic balancer to get to the timing gear sprocket.It has a blade attached to it with 3 fins in between the fins is a little dip that is the crankshaft position.align that dip with the mark below the crankshaft position sensor.then you have to do the same with your camshafts.Then replace the belt and spin the the crankshaft clockwise to the aligment mark they should all stop on their marks.

Apr 18, 2010 | 1996 Mitsubishi Eclipse

1 Answer

I have a 1994 eagle talon i replaced the water pump and put on a new timing belt and i can not get the timing right i have tried everything i know what could i be doing wrong? I have made sure the number...


I'm looking at the manual (68030 Haynes) and it shows that if you have the DOHC you make the 2 marks onthe camshafts meet in the center.

That would be at the 3 o'clock position for the left one, and 9 o'clock position for the right one. the crank sprocket and oil pump sprocket align exactly with the timing marks.

NOW, on the SOHC single cam pulley, crankshaft and oil pump pulley all are to be aligned with their index marks, centered, and the balance shaft is to be with the weighted side down to prevent vibration.

I've done the SOHC and the marks are fairly centered when instlalling. Once you've got the belt on in either engine, you should rotate the engine in the normal direction for 2 full revolutions and recheck the timing marks at all positions, readjust, rotate and recheck until set on the marks.

Good luck,

Feb 21, 2010 | 1994 Eagle Talon

1 Answer

Alternator belt replacement


Check Your Timing Belt
  • Check your owner's manual for the recommended mileage for replacing your timing belt. Replacement for Hyundai Sonatas is 60,000 miles.
  • Locate the timing belt and examine it for breaks, damage, fraying, worn spots or looseness.
  • Inspect the belt for cracked or missing teeth that may be the result of foreign material collecting between them.
  • Determine if the timing belt damage is on both sides. Single-side damage may be caused by the timing belt's guide.
    Remove Your Timing Belt

  • Disengage the negative battery cable.
  • Turn the tensioner arm to the right 14° and take the timing belt off its pulley.
  • Take out the coolant pump, idler, tensioner and crankshaft pulleys and both timing belt covers.
  • Remove the engine's mounting insulator and mount bracket and the auto tensioner.
  • Align the crankshaft's timing mark so the first cylinder piston is at "Top Dead Center" (TDC). The camshaft sprocket and cylinder head cover timing marks also should align.
  • Unfasten the timing belt.


    Replace Your Timing Belt

  • Examine the cam and crankshaft sprockets. Replace if there is excessive wear or other damage.
  • Position the new timing belt on the sprockets.
  • Relax the timing belt tensioner so it can make contact with the belt. Adjust the belt to the tension recommended in your vehicle owner's manual. Also align the timing indicators on the cam, crank and other sprockets.
  • Return the engine to the 0° mark by turning it two revolutions in the direction of travel.
  • Secure the timing belt cover and reinstall whatever was removed to access the timing cover.
  • Reconnect the negative battery cable and any other items that were disconnected.
  • Start the engine and look for leaks


Nov 24, 2009 | 2000 Hyundai Sonata

1 Answer

I have 95 eagle summit with 1.8 mitsubishi engine timing belt broken need alignment diagram to put it back together right


pdftown.com scroll to bottom of page and look for 1993-1996 Mitsubishi Mirage, follow the links 1 2 3 you will find what your looking for

Sep 23, 2009 | 1995 Eagle Summit

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
1995 Eagle Summit Logo

723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

Marvin
Marvin

Level 3 Expert

84966 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Stewart Dibbs

Level 2 Expert

406 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...