Headlight condensation how do I remove the condensation under the headlight cover?

no problem told at all, surely not lookin for fun and kicks?
EGR Orifice,
AC expansion valve orifice.
or what tell what it does, or the problem told
2.2Liter, L61 engine.

I think you meant this. for HVAC AC cooling problems.
air conditioning, is located at the evaporator core close by.
Expansion (Orifice) Tube Replacement the service manual covers this, see my last link
EGR on some it is in the rusty exhaust pipe just to the rear of the main EGR valve.
manuals

https://eautorepair.net/Marketing/Default.asp

• 
  

• 
• 
• 
• 

saturn aura replace headlight bulb with bumper on!
[img src="https://i.ytimg.com/i/QnvVxud6_7t7W6Rm2ABgnA/1.jpg" alt=" [a href="https://www.youtube.com/channel/UCQnvVxud6_7t7W6Rm2ABgnA"]execlon's channel
44 50,720

• Start at:

Published on Mar 8, 2013
Remove 5 -10mm bolts 4 on plastic cover under hood 1 on air cleaner hose.
Remove 2- clips with flat head on plastic cover under hood
Remove 6 7mm screws (headlight brackets)
Lift up and over hood latch the center cover plastic
Pull inner side of headlight outwards and outter side towards middile of car and out.
Its hard but you can get it to pop over the corner of fender. I did it all in around 15 minutes
Dont give up it can be done! sorry about not having more video my hands were busy at the end.

I changed my 2001 Toyota Highlander headlights recently. First, remove the grille. There is one screw in the center which will require a loonng Phillips screwdriver to reach it, down behind the grille, right in the center. Then remove the four plastic clips at the top by prying them up with a small flathead screwdriver. The bottom just pulls forward. Important: Now go to each side of the car, and in front of each fender well, there is one clip that holds the bumper cover on. Pull the top corner of the bumper cover toward you to release the clips, one on each side, at the top corner, along the front of each fender well where the bumper cover meets the fender. The bumper cover can now be loosened along the top without entirely removing it. It just pulls forward. Inspect the underside of the bumper cover for broken clips and replace as necessary. Now remove the two bolts that hold down each headlight at the top. Disconnect the wiring and bulbs and wiggle the old headlights out. Install the new ones and reverse the process. If your AC isn't blowing cold, check the condenser for leaks before you reinstall the grille. A new aftermarket condenser/filter dryer is easy to install by removing the battery and tilting the radiator back to get the condenser out. A replacement only costs $75 and can be swapped out in one half hour with a few metric sockets. Then you will need to recharge the AC system with R-134a, which is easy. Just buy a R-134a kit with hose at Autozone and follow the directions. $50 Replacement fog lights are only $52/pair for aftermarket. You may consider replacing those as well. They have a strange installation with clips and you will need to pry/bop them forward, not remove them from the back. They are aggravating to replace but not technically difficult.

you are talking aftermarket headligth covers? , the head lite itself cant not be taken appart, your best bet is to drill a small hole in the lower part ofthe headlight so moisture can be release, this will help but in the long run you'll need to replace it

remove 2 10mm bolts attaching top of headlight to the radiator support.

remove plastic clip attachinig headlight to top/front of fender.

remove 5 phillips screws on top of grill.

carefully pull out grill enough to remove 1 10mm bolt attaching headlight to radiator support and use slotted screwdriver or prybar to seperate headlight tab from the bracket that goes under the bumper cover.

with a little effort and wiggling pull out headlight assembly.

if you have the regular headlights(not the HID) there is a TSB for that at the dealer and they will fix it for free as long as you are under the 36000 miles,,anyhow to get the headlight out you need to remove the front bumper cover,,pop the hood, remove all the pushpin that hold the plastic panel on near the front area then remove the plastic cover,,,,,then there are some phillips head screws along the front of the top of the bumper cover take these out,,,,now remove both front wheels,,remove the bolts that hold the inner fender liners inplace there are some in front and under the lower bumper cover take these out too,,,,then under the front bumper cover at about the middle there will be 2 bolts i think 10mm remove theses to,,,,now where the side of the bumper cover meets the fender inside there are 3 bolts on each side remove these i think they are 7 or 8mm and then pull the bumper cover off,,,if you have fog lights disconnect the plugs,,then you will see all the bolts holding the headlight in take them out and then it comes out,,,,i know its alot of work just for a headlight ,,,,

Here's a great video that will also show you how to remove the marker light.">

found this online- haven't tried yet though--
How do you change a headlight bulb on a 2003 Toyota Celica GT? Under the plastic covering the headlight there is a lot of fog and condensation and I want to clean it off, so how do I take off the plastic that covers the headlight?

• 9 months ago

Seem to be seal is wear off
already on the front cover
The way to open that
1. There is four screws at the back of
the headlights and unscrew them
2. Pull the headlight and dry it
by wiping or heat of the sun or
anything that can release the fog
3. Buy silicon and seal the headlight
gap with silicon and let it dry for a hour
This will help kept away fog
and condensation for sure

lift your bonnet up
see if there are any screws possible no
it should clip on
then just pull off and put on same way it should be like a long bent clip up top the actual cover