How do I check engine fault codes? - 1998 Chevrolet Metro

Holden Fault Codes - Delco - AFI Australia - Fuel Injection ...

afiaustralia.com.au > tech-tips > 91-fault-codes > 313-h...

Holden Fault Codes - Delco. Diagnostic Fault Code List for Delco System Camira, Commodore VN-VP 12 No spark pulses at CPU or else good system, ...

fault codes barina Questions & Answers (with Pictures) - Fixya

www.fixya.com > tags > fault_codes_barina

Holden barina tk 2007 engine won't start. ? run the fault codes check that the cam shaft is turning ( broken timing belt) check immobiliser for correct operation ...

Holden Barina P1700 Engine Trouble Code

p1700.enginetroublecode.com > holden-barina

Holden Barina P1700 OBD-II Diagnostic Powertrain (P) Trouble Code Information Page. Reason for Holden Barina P1700 and find the solution for the code ...

P1100 Holden Barina DTC Code ' EngineDTC.com

enginedtc.com > p1100-holden-barina
Your Holden Barina engine control system detects a problem, the computer stores the diagnostic trouble code P1100 in its memory. To figure out what is wrong ...

first thing is to find the reason for the limp mode as it has been activated to protect the engine and transmission
do this by having the fault codes read ASAP then fixing the fault

The check engine light n or reduced power light comes on when the on-board computer detects a fault in engine driveability or performance, transmission control system or transmission, or the emissions system, and a fault code is set and stored in the computer. Faults that can set the check engine light can range from a vaccuum leak, engine mis-fire, low engine compression, faulty sensor such as O2 sensor or other engine sensor, hydraulic pressure loss in transmission, transmission shift solenoid, open/short in wiring harness, emission evaporative system leak, or one of over a hundred different reasons. The only way to know what set a fault code and turned the check engine light on is to have a diagnostic scanner hooked up to the on-board computer and read it for stored diagnostic fault codes. Many auto parts stores will do this service for free- (like auto zone)check with you local parts stores. If none in your area do, then you will have to take it to a shop and pay to have the computer read for stored fault codes. Without knowing the fault codes numbers, it would be irresponsible to guess as to the cause as there are hundreds of possible causes.

I’m happy to assist further over the phone at https://www.6ya.com/expert/john_4009e70b6376c95f

2016 Volvo tTruck D13 I shift
I have engine lights on the cod#
sa 16 dtc p20ee00 on truck volvo 2016
Anybody can help me please

Check engine light on but no code Ricks Free Auto Repair Advice

Take it to a local autoparts store and ask them to read the engine fault codes. Fault codes will help determine where the problem is. Reading fault codes is usually a free service.

Also make sure that your gas cap is tight as a loose gas cap can cause the check engine light to be turned on.

Please report here as to what fault codes you have and what problems you are having with the operation of your vehicle.

Thanks

Bob

lol
thats a new one
there is no check engine sensor.
theres lots of different sensors take tell a computer to set a code and turn on that light.
ask autozone to check the codes for you for free.
its a free service they offer.
the codes will tell you whats wrong
probably an o2 sensor.
ask them if they have it in stock.

keep me posted
thank you
jm

BMW engine light

Comes on if DME engine management system self diagnostic fault detected. Will stay on until codes are called up and memory erased.

With OBD read the code as follows. Turn on ignition key, press accelerator pedal to the floor five times within 5 seconds. The check engine light will remain on for 5 sec , blik off, come on for 2,5 sec, go off for 2,5 sec and fault code will begin to flash. If more than one fault exist 2nd fault code will be separated by 2,5 sec pause. after fault codes there will be a 0.5 sec flash and light will remain off. to read codes again do procedure again.

Canceling of codes. make sure fault code is present (short blink and light goes out for long period), depress throttle pedal for at least 10 sec. read fault codes again and check for code 1444 (no faults stored.)

Check also the following, fuel pump, oxygen sensor, fuel injectors, engine coolant temp sensor, idle speed control valve, mass airflow sensor and too many other things.

when the engine light comes on the defect on the engine can be a blocked exhaust system or an air leak to the manifold. the oxygen senser monitors the runnig condition of the car and will inform you that the engine is not run correctly. diagnostic can tel you the defect

Engine-light-help.com

P1100 Induction Control Motor Position Sensor Fault

P1101 Traction Control Vacuum Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1102 Traction Control Ventilation Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1103 Turbocharger Wastegate Actuator

P1104 Turbocharger Wastegate Solenoid

P1105 Fuel Pressure Solenoid

P1294 Target Idle Speed Not Reached

P1295 No 5 Volt Supply To TP Sensor

P1296 No 5 Volt Supply To MAP Sensor

P1297 No Charge In MAP From Start To Run

P1300 Ignition Timing Adjustment Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1390 Timing Belt Skipped One Tooth Or More

P1391 Intermittent Loss Of CMP Or CKP Sensor Signals - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1400 Manifold Differential Pressure Sensor Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1443 EVAP Purge Control Solenoid '2' Circuit Fault

P1486 EVAP Leak Monitor Pinched Hose Detected

P1487 High Speed Radiator Fan Control Relay Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1489 High Speed Condenser Fan Control Relay Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1490 Low Speed Fan Control Relay Fault

P1492 Battery Temperature Sensor High Voltage

P1494 EVAP Ventilation Switch Or Mechanical Fault

P1495 EVAP Ventilation Solenoid Circuit Fault

P1496 5 Volt Supply Output Too Low

P1500 Alternator FR Terminal Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1600 Serial Communication Link

P1696 PCM Failure EEPROM Write Denied

P1698 No CCD Messages From TCM

P1715 Pulse Generator Assembly

P1750 Solenoid Assembly

P1791 PCM ECT Level Signal To TCM Circuit Fault

P1899 P/N Position/Transaxle Range Switch Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1751 A/T Control Relay

P1791 Engine Coolant Temperature Level Input Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1795 Throttle Position Input Circuit To TCM - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code