Its inside the pan and behind the trans filter assembly within the transmission,,, about 14 bolts to drop the oil pan ,, 2 hold the trans filter in place,,
Here are the instructions on the jeep forum website AW4 Solenoid replacement write up no 56k JeepForum com
SOURCE: jeep codes location of unit
Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.
SOURCE: 2000 jeep cherokee sport 4.0
I believe that year had distributorless ignition, instead it uses a form of coil on plug ignition system.
If you open the hood, stand at the front of the vehicle. Look to the left side of the engine, around the bottom of the valve cover (The valve cover is where the oil fill cap is. The oil fill cap is on top of the valve cover), at the bottom of the valve cover on the left side you will see a series of humps. Those series of humps is the coil packs, the coil packs are all in one long piece held down by three or four bolts.
Take out those bolts, gently pry up at the ends of the coil pack and it will eventually come out. You'll see on the bottom side the spark plug boots are attached to the coil pack. After you get the ignition coil pack off, you will see the spark plugs under where the coil pack came from, the boots on the coil pack sit directly on the spark plugs.
SOURCE: 2000 jeep grand cherokee limited starts in 3rd gear
oil pressure problem should be checked independently of other problems...Use a good accurate mechanical gauge to check. If pressure is good (no less than 15psi at idle hot (I prefer to see at least 20) check dash grounding, block ground and if OK, change sending unit. Dash and body ground can influence operation of shift and body control modules so indirectly your problem may or may not be related, depending upon what you find while testing. And it could turn out to be a defective module! They are expensive and just plugging new ones in may work, but then again, it might not. I might be totally incorrect on this...that's the value of actually being there instead of doing this by "remote control".
If you read the numerous posts pertaining to all vehicles, you will see that you are not alone with electrical problems...As long as the engineers who design this stuff, keep using "modules" to replace ordinary simple and reliable systems, we will continue to have these problems. Do some testing and I'm sure you will find a solution! (I'm still waiting for someone to make a program for a PC that will give a complete readout of every system in a vehicle, including exact faults instead of general system "suggestions")
Good luck
SOURCE: shift indicator light 1999 Jeep Grand Cherokee
There are two parts to it, a voltage resistor, and the EL panel itself.
You need to remove the console first. There are 2 screws under the front rubber pad, two under the cup holder, two in the bin. Remove those six first, take the storage bin out, then slide the rear cupholder out, remove the two screws under the cup holder, and one in front of it.
There are a total of 6 flat screws, and 3 self tapping screws you have removed.
Put the parking brake on, shift the tranny to N, and the transfer case to the middle position if equipped.
Remove the entire console. Slide the shifter beezel as far up vertically as you can. There are 4 clips you ned to remove to do it.
You will see a blue and black wire running into the back. Follow those wires to the resistor. You will see a transparent EL panel attatched to the resistor by two clips.
Usually, one or both of these clips has come loose, causing the light to work intermittantly. Clip them back on, and turn on the headlights to confirm that the light works correctly now.
Re-install everything in the opposite order.
SOURCE: where is the shift solenoid on a 99 jeep cherokee
There are four solenoids and they are inside the transmission, you must remove the pan from the bottom of the transmission and they are right there bolted to the transmission valve body assembly.
754 views
Usually answered in minutes!
×