Honda vtec 1.5 jazz, drivers mirror

To fit it you need to pop off the mirror plate itself, remove the (7 I think) screws to access the wing mirror cover clips. Squeeze those to release the cover, remove the cover to expose the indictor unit which can then be unscrewed (2 screws) and the push-on electric plug removed. Reverse for putting back together.

Pretty easy. The hardest part was getting the mirror off gently.

Hope that helps. Unfortunately I didn't take pics, but is really straightforward.

Go to Connemera Market, Palayan, Trivandrum. I've seen so many of it there.

With the help of diagnostic computer go to EPS and clear the present and history error codes, if any. This problem usually arises when replacing the battery.

Likely to be the actuator/motor inside that has failed. Order one off eBay that offers returns an find out how to fit it. Should be job done!
If not its likely to be a more serious electrical issue good luck with that..

Instructions1.

• 1

Remove thedoor panel. Refer to your Honda Accord repair manual for theinstructions in removing the door panel. Unhook the rods and connectors on theinside of the door panel and set it on the floor.

• 2

Remove thefilm covering the access to the side mirror. It's difficult to avoid damaging thefilm while removing it so you will need to purchase a new piece of filmcovering when you buy a new side view mirror.

• 3

Reachthrough the service hole into the mirror housing with a screwdriver. Loosen thescrew that holds the mirror. Twist the screw out with your hand.

• 4

Reacharound the door and support the mirror with your other hand. Continue to twistthe screw out, then catch the mirror as it drops out when you remove the screwcompletely. Put the screw in a safe place so you don't lose it.

• 5

Installthe new side view mirror by positioning it where the old mirror was. Insert thescrew you took out in Step 4 and twist it in with your hand. Insert ascrewdriver into the service hole to tighten the screw.

• 6

Replacethe film covering that was damaged when you took out the old mirror. Push itinto place in the indentation on the door.

• 7

Sit in thecar seat and adjust the mirror so you can use it properly.

You can determine where your car was made by examining the VIN
Example Description Vin # ------- -------------------------------- J ╗ H ] - JHM = Honda Motor Co. passenger car M ╝ E ╗ EG1 = D15B7 (93-95 S) G ] - Engine: EG2 = B16A2 (96-97 VTEC), B16A3 (94-95 VTEC) 2 ╝ EH6 = D16Y7 (96-97 S), D16Y8 (96-97 Si), D16Z6 (93-95 Si) 1 ] - Body/Transmission: 1 = 2-door manual 5-speed 2 = 2-door automatic 6 ] - Vehicle Series: 4 = S 6 = Si 7 or 9 = Si with ABS, or VTEC ? ] - math check digit R ] - Model Year: P = 1993, R = 1994, S = 1995, T = 1996, V = 1997 S ] - Assembly Plant: C = Sayama, S = Suzuka, T = Tochigi 0 ╗ 0 ║ 5 ] - Serial number, based on the sequence off the 7 ║ production line 9 ║ 3 ╝

********

door pad removal look for little pop outs take the pop outs off and thenremove screw then remove the mirror cover then pull on the bottom of door then pull on the side and then pull off trim up and out then you will see a vapor barrier remove it then you see the inside handlejust acouple of srews /please rate my response thank you very much

hey, I replaced a mirror on a 2002 civic lx coupe.

1) Pry off the small pastic traingular piece from the interior of your door.
2) Disconnect the wiring to the mirror
3) There will be 3 bolts that attach the mirror to the car, remove these and the mirror can be removed. To put on the new mirror just do everything in reverse

Just make sure you order the right mirror, I accidentally order the mirror for the sedan model the first time and they are not interchangable.

Hope this helps

I would bet it's a mirror-image (sorry...) of the driver's side installation. See http://www.civicforums.com/forums/21-i-c-e-electrical/289740-diy-front-door-speaker-install-coupe-sedan.html and migrate ~1/3 the way down to the pic labeled "Remove Sail Panel." If you already have the mirror it is probably as simple as replacing the existing outside cover with the mirror. If you're not sure you can do this on your own ask a mechanically-minded friend for help. Search the internet with http://www.google.com/search?hl=en&q=%2B2003+%2Bhonda+%2Bcivic+%2Bfront+%2Bdoor+%2Bmirror for 50k hits - good luck!