Question about 2004 Infiniti FX35

Open Question

Remove door lock actuator

How to replace right front door actuator with after market one

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix LHS front door remote. Lock on holden statesman wl


more than like if its just on door that wont look and the hoon sounds the door actuator will be faulty and you will need to replace the actuator.
To do this you will need pull the inside door handle off.
remove all door trim covers to access screw and disconnect mirror wiring.
remove all screws around door trim.
very carefully remove door trim once the trim is off you see a plastic inner door liner don't rip gently remove half .
look inside door and you will see the door actuator and lock,carefull lift up locking tabs so you can remove all door rods from actuator.
on the outside of door undo the 3 bolts and actuator will come out.
get the new actuator and fit it the same way the old one come out.
Before refitting the trim grab some silicon and reseal plastic to door to keep water out..

Dec 06, 2014 | Holden Cars & Trucks

1 Answer

How to remove the in door of a 1990 bmw 325i? And also the drivers door will not lock when i turn the key the other doors lock but the drivers door doesnt how should i go about fixing that?


Sounds like you need to replace the power door lock actuator for the driver's door.


E30 Models
  1. Remove the door panel and the water shield.
  2. Disconnect the wiring from the actuator. Remove the screws and pull the actuator off the linkage.
  3. When installing, move the actuator and linkage to the locked position.
  4. Connect the linkage to the actuator and loosely install with the screws.
  5. Compress the actuator drive to take out any play in the linkage and tighten the screws.
  6. Test the locks and install the door panel.

E36 Models
  1. Remove the door panel and water shield.
  2. On the front doors, remove the guide rail nut and pull the guide rail down. Disconnect the wiring and the linkage from the actuator.
  3. On the rear doors, remove the window and the access panel. Disconnect the wiring and the linkage from the actuator.
  4. Remove the 3 bolts holding the latch and actuator to the door structure.
  5. Install in reverse order using threadlocker on the bolts.

Mar 16, 2011 | 2003 BMW 325

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

Replace door actuator


1999 Ford Explorer Door Lock Actuator
REMOVAL:
1.Remove the front door trim panel.
2.Remove the water shield.
3.Remove the power door lock actuator.
4.Disconnect the electrical connector.
5.Drill out the rivet.
6.Disconnect the actuator rod.
7.Remove the actuator.
------------------------------------
Attached images 4834d1192136560-door-panel-diagram-ford-explorer-80937917.gif

Aug 08, 2010 | 1999 Ford Explorer

1 Answer

How do you replace the regulator for the power window on the 2002 ford explorer


Regulator - Power Windows - Front Door
  1. Remove the front door trim panel as follows:
    1. Remove the front door handle bezel.
    2. Remove the front door window/lock control switch bezel.
    3. Disconnect the window/lock control switch electrical connectors.
    4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
    5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    6. Remove the exterior mirror control switch from the front door trim panel.
  2. Remove the front door speaker.
  3. Remove the interior molding.
  4. Disconnect the door lock actuating rod at the door handle assembly:
    1. Release the door lock actuating rod clip.
    2. Position the door lock actuating rod aside.
  5. Remove the front door weather shield.
    CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
    NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
  6. Remove the 2 front door window glass-to-regulator bolts or rivets.
  7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
  8. Secure the front door glass in the full up position with tape.
  9. Disconnect the window regulator motor electrical connector.
  10. Remove the 4 window regulator assembly nuts.
  11. Remove the window regulator assembly.

    0b00886.jpg

    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer

To install:
  1. Position the window regulator assembly.
  2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
  3. Connect the window regulator motor electrical connector.
  4. Remove the tape securing the front door glass in the full up position.
  5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
  6. Install the front door weather shield.
  7. Connect the door lock actuating rod at the door handle assembly:
    1. Position the door lock actuating rod into proper location.
    2. Attach the door lock actuating rod clip.
  8. Install the interior molding.
  9. Install the front door speaker.
  10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.

  1. Raise the front door window glass to the full up position.
  2. Remove the interior door handle.
  3. Support the front door window glass.
  4. Disconnect the front door window regulator motor electrical connector.
  5. Remove the equalizer bracket nuts.

    4945f24.jpg
    Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
  6. Remove the front door window regulator by removing the rivets and nuts.
  7. Remove the front door window regulator motor retaining bolts and then remove the motor.

    52a6816.jpg

    Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).

Hope this help (remember rated and comment this).

Mar 24, 2010 | 2002 Ford Explorer

1 Answer

Sliding door does not lock with button on front doors or keys


Your question is alittle vague,...so Ill do my best...If your van has central locking (all the doors lock when you lock the drivers door with a key) then I can easily say that the actuator for the sliding door lock has malfunctioned....However if you are implying that you cant lock the sliding door from the outside using a key then it is because the linkage inside the door has came apart (Both issues would cause the door not to lock with the power lock button) If it is the linkage this is easily fixed by removing the interior panel on the slider and reconnecting the metal rod to its rightful place, if it is the actuator you have to replace it by removing the interior panel..Good luck

Oct 08, 2009 | 2006 Chrysler Town & Country

1 Answer

How do I replace the door lock actuator on a 1999 Mercury Villager w/o damaging the connecting rods and door track?


SECTION 501-14A: Handles, Locks, Latches and Mechanisms 1999 Villager Workshop Manual REMOVAL AND INSTALLATION Actuator —Power Door Lock, Front Removal
  1. Remove the front door latch. For additional information, refer to Latch—Front Door .
  1. Remove the power door lock actuator from the front door latch.
    1. Release the locking tabs.
    1. Remove the power door lock actuator from the front door latch.
583b623.gif
go here too

http://groups.yahoo.com/group/villagerquest/

Sep 26, 2009 | 1999 Mercury Villager

1 Answer

1999 GMC suburban locks seize in locked postion


I just bought a 1999 Suburban and all of the door lock actuators were bad including the rear (barn style door) while I was replacing the rear door acuator I noticed that even with the factory mounting bracket on the actuator it was causing the door lock rod (the rod from the keyed cylinder lock to the actuator) was on a bind......the solution I came up with is adding an additional 3/4" spacer between the factory mount bracket and the door attach point. this solved any binding and the door lock works great now........also I used a lubricant on all the doors where the rods run through the plastic guides, which seemed to help quite a bit! Hope this help's.

Aug 28, 2009 | 1999 GMC Suburban

2 Answers

Broken exterior door handle,passenger sider ,sliding


Got this idea from mpvclub.com: Get some stainless or aluminum sheet metal screws, drill pilot hole into the handle and into the receiving part behind, then screw in the screw. Do on both sides of handle (get appropriate length screw.) When done, get some putty or hardener to fill in the screw slot, let dry, then sand smooth, then paint with body color. Result is great and inexpensive.

Jan 26, 2009 | 2004 Mazda MPV

1 Answer

1996 Ford Bronco door lock actuator


These directions might sound a little goofy. I'm trying to orient your location with front and rear rather then left and right because it depends on which door you are working on. Front is towards front of rig and rear, oh I think you get it.
1. Close window on door. 2. Using a flat screw driver pop off trim under inside door handle. I think there is a groove in the plastic to which the screw driver can be inserted. Remove screw. 3. Using same screw driver pop off trim panel with door lock and window control switches. Start lifting from end located at panel closest to the front of the rig. The panel towards the back end has a pivot point which holds the back of the panel into the arm rest. Dis-connect the two switches from the trim panel. 4. Again, using flat screw driver, pop off the trim pannel located at the upper door/window frame nearest the back of the rig. Remove screw. 5. Lift up the door panel to remove. Be careful the light bulb is attached to the door panel. Rotate light socket 90 degrees and remove. 6. From the rear of the door pull back the platic stick-on barrier. Don't remove the whole thing just pull it leaving about half of it towards the front of the door stuck on. 7. Remove the one 11mm bolt, located towards the bottom of door, which holds the rearwindow guide. Don't remove the two 11mm bolts which hold the horizontal brace. Nothing else needs to be removed, leave all rods and attachments in place. They all attach the the door latch and are not of any further concern.
8. Now the easy part. The actuators and door latches are separate components. The actuator slides onto the door latch via two metal guides located on the door latch. The actuator is held into place with a plastic locking tab. The locking tab is part of the actuator housing. 9. This tab has to be pushed in to release actuator from latch. 10. Find on ouside of door - rear where the latch fingers? (I don't know what else to call them) are located in the notched door frame. At the bottom of the notch is a very narrow opening, just a ****. This **** allows access to the locking tab on the actuator. 11. Orient the screw driver in the end of the **** closest to the interior. Working on a right door, looking at the locking fingers, facing the front of the rig, your screw driver would be inserted at the left side of the ****. Pushing a flat screw driver into the **** will push the locking tab allowing the actuator to slide off the door latch. 12. A flat screw driver or other small pry tool can be inserted between the actuator and the door lock to help slide the actuator off the metal guides. The pry unit can be inserted where the rod from the interior manual door lock stem is attached. Mine had a yellow snap/flip keeper. 13. The actuator slides off from the interior towards the outside door panel. 14. Simple put pressure onto the locking tab with one screw driver and gently pry with the other one and the actuator should slide right off.
15. I picked up an actuator at a u-pull it wrecking yard for five bucks and it worked fine. Dealer wanted $90.00 and auto parts wanted $127.00. When I pulled my actuator from the wrecked rig all door panels and interior where stripped. It took me literally 20 seconds to pull the actuator. 16. To install new unit slide actuator onto door latch rails and let locking tab click into place. You might have to manually move the interior door lock stem up and down until the finger on the actuator lines up with a hole on the plastic part of the interior lock stem.
16. I Want to thank TommyRox in Texas on Ford Truck World and rivguy on automotiveforums.com for their posts.

Jun 18, 2008 | 1996 Ford Bronco

Not finding what you are looking for?
2004 Infiniti FX35 Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...