Question about Land Rover Discovery

Open Question

Where is chassis number on landrover discovery 2014 GS

Where is the chassis number located

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
martin538
  • 117 Answers

SOURCE: need head bolt torque settings for 200 landrover discovery 4.0 liter 241 cu.in.

Stage 1 20nm
Stage 2 +90 degrees
Stage 3 +90 degrees

Posted on Apr 13, 2009

Ad
  • 136 Answers

SOURCE: i connect a 1997 landrover discovery computer to the 1994 landrover discovery and it won't start.

if it is a mems unit , it will need to be programed to the key fob and alarm . (there is no way round it).

Posted on Sep 03, 2009

  • 149 Answers

SOURCE: chassis number location other than on vin

Location
The Vehicle Identification Number (VIN) plate is stamped on a plate attached to the bonnet locking platform. The VIN is also stamped in the following locations:
1) On a plate behind the LH lower corner of the windscreen.
2) On the chassis RH longitudinal behind the rear wheel.

Posted on Feb 22, 2010

  • 149 Answers

SOURCE: 2000 landrover discovery td5 GS abs tc and hill

Suggests either Wheel Bearing, ABS Sensor Fault, or Shuttle valve. Best to get it to a dealer and on the computer for them to diagnose what exactly is wrong.

Posted on Feb 24, 2010

  • 3741 Answers

SOURCE: I have a 2004 landrover discovery, where is the

As a Land Rover Tech I can tell you that it is true that there is no filter on the series2 there is a small screen at the bottom of the pump pickup that acts as a filter,If you feel this is clogged you can remove the pump by pulling up the rear cargo area carpet as recommended above then just use break clean to clean the screen.Make sure you replace the pump gasket as a faulty gasket will cause a check engine light and a little trick I use is to put a small amount of vaseline on the gasket to ease installation.Also a quick note on series 1 filters is that the lines usually cease up causing the connections to break or damage when removing.I highly recommend getting the repair kit available at the dealer or rovers north before attempting to replace the filter . BUT IN REGULAR 2004 lan-drover discovery there is fuel filter located. Removing the fuel filter The fuel filter is located on bulk head, to left hand side of the engine.
1: Start by cleaning the area around the filter head.2: Place a container beneath the fuel filter to catch any spillage.3: Loosen the bleed screw using a 10mm spanner4: Unscrew the drain tap on the bottom of the filter until the fuel starts coming out into your the container.5: Once all the fuel is drained from the filter, unscrew the whole filter assembly.

Fitting the new fuel filter 6: Clean the seal & seating on the new filter.7: Put a small amount of fuel around the rubber seal to lubricate it.8: Screw the new filter onto the filter head and tighten by hand.10: Tighten the bleed screw.11: You can now crank the engine until fuel is drawn through the system and the engine starts.Job done!

This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya


Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm trying to locate chassis' number and location on Australian land rover discovery 2000 model?


The guys on this Landrover Forum should be able to help you with that. If not try one of the other LR Forums. Just google them.
Here is the link for the Forum.......

http://www.aulro.com/afvb/discovery

Dec 17, 2015 | Land Rover Cars & Trucks

1 Answer

Good day, I own a Discovery 2002 Series II, TD5, GS. Question: Drive belt part number PQS101500 is smaller than PQS101510, Landrover supplied me the latter, which was too big! The former was correct. What...


Some Series II Discoveries has the ACE(Active Cornering Enhancement) option which had an additional hydraulic belt drivem pump, these cars require a larger belt. It is likely that they sold you a belt for a car with ACE

Dec 06, 2010 | 1996 Land Rover Range Rover

1 Answer

How do i fit a towbar to a landrover discovery 2


towbar on a disco 2 is a straight forward bolt on job it attaches to the rear chassis and crossmember any good quality towbar kit will come with all bolts and washers you need plus instructions . if you get genuine landrover electrics they plug straight in without having to cut or join any wires.

hope this helps

Sep 14, 2010 | 2003 Land Rover Discovery

1 Answer

Need radio code for 1999 landrover discovery 1


Hi,

Can you confirm what brand the stereo is? If it is the Visteon brand that Landrover fit then I can help. Just let me know.

Thanks.

Apr 03, 2010 | 1999 Land Rover Discovery

1 Answer

Chassis number location other than on vin plate.2004 discovery es 2.5 diesel. thank you.


Location
The Vehicle Identification Number (VIN) plate is stamped on a plate attached to the bonnet locking platform. The VIN is also stamped in the following locations:
1) On a plate behind the LH lower corner of the windscreen.
2) On the chassis RH longitudinal behind the rear wheel.

Jan 24, 2010 | 2004 Land Rover Discovery

1 Answer

2000 landrover discovery td5 GS abs tc and hill decent lights on the dash. any help apreciated!!


Suggests either Wheel Bearing, ABS Sensor Fault, or Shuttle valve. Best to get it to a dealer and on the computer for them to diagnose what exactly is wrong.

Jan 04, 2010 | 2000 Land Rover Discovery

1 Answer

I connect a 1997 landrover discovery computer to the 1994 landrover discovery and it won't start.


if it is a mems unit , it will need to be programed to the key fob and alarm . (there is no way round it).

May 21, 2009 | 1994 Land Rover Discovery

1 Answer

I am trying to find out if the wiring is in my landrover 300tdi


any aftermarket lights have to have the wire loom ran. when you run the loom make sure that it is protected and out of the way of things. also when going through any peace of steel make sure that you use a gromet so the wires don't get cut.

Dec 09, 2008 | 1998 Land Rover Discovery

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...