Replacing the serpentine belt
Write down a diagram of how the belt runs marked with O to mark where the pulleys are undo or release tensioner remove and replace belt.
SOURCE: replacing timing belt on daewoo nubira 2000 model
Instructions
Difficulty: Moderate
Things You’ll Need:
Step1
Raise and support the vehicle
on jack stands. Remove the intake air temperature wiring, the breather
hose and intake air hose. Take off the air cleaner assembly.
Step2
Remove the right wheel. Remove the accessory belts. Remove the
crankshaft bolt and the crankshaft pulley. Remove the power steering
bolts and the timing belt covers. Temporarily install the crankshaft
bolt and turn the engine clockwise until the mark on the crankshaft
pulley, which is a triangle stamped into the crank sprocket, is aligned
with the corresponding triangular mark on the block.
Step3
Make sure that the timing marks are aligned on the camshaft sprockets.
These are a line on each sprocket that runs through a tooth on each
sprocket. These lines should line up in the middle between each
sprocket and point toward each other. If they do not line up, turn the
crankshaft one more time and they will line up. It takes two turns of
the crank to one complete revolution of the cam.
Step4
Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water
pump clockwise away from the belt and loosely tighten the bolts to keep
it there. Remove the timing belt
.
Make sure the timing marks are aligned and install the new belt
starting on the right side from the crank sprocket and working
counterclockwise. Keep all the belt tension on the right side away from
the tensioner.
Step5
Loosen the bolts in the water pump and rotate the water pump
counterclockwise to apply tension to the belt. Watch the tensioner,
which is above the water pump, and apply tension with the water pump
until the pointer on the tensioner lines up with the notch above it.
Lightly tighten the water-pump bolts.
Step6
Turn the engine
two more times and align the timing marks perfectly. Loosen the
water-pump bolts and, using the ratchet, apply tension to the belt
until the tensioner pointers are aligned. Tighten the water-pump bolts.
Step7
Install the timing-belt covers and the bolts in the power-steering pump
and tighten. Remove the crankshaft bolt and install the crank pulley
and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds
of torque. Install all components in reverse order of removal.
SOURCE: 2000 daewoo nubira need serpentine belt routing
The following link will take you to a diagram for your car. Best of Luck!
Greg
http://www.mvreader.com/multiview/dayco/zoom.php?zoom_item=C0000B&l=n&catalog=auto&category=2
SOURCE: Newly replaced timing belt was broken in my daewoo nubira 2000
Yes you should always do the water pump when doing the timing belt. belt tension too tight can cause the break as well as a bad water pump or idler pully, these should all be replaced when you do a timing belt to save yourself this exact headache later on.
SOURCE: serpentine belt broke need diagram to replace
look under the hood they are usually a sticker there or on the shock tower under the hood sometimes or in the owners Manuel
SOURCE: replacing timing belt on daewoo nubira 2000 model
My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.
CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2000/make/daewoo/model/nubira/2000_daewoo_nubira_timing_belt_diagram_marks.htm
311 views
Usually answered in minutes!
×