Camshaft torque 4.6 camshft torque

1. Hand start all the camshaft bearing cap bolts.
2. Tighten the camshaft bearing cap bolts in sequence to 10 Nm (89 lb in).
3. Loosen the center intake camshaft bearing cap bolts 1, 2 and the center exhaust camshaft bearing cap bolts 3, 4.
4. Retighten the center camshaft bearing cap bolts 1, 2, 3, 4 to 10 Nm (89 lb in).

Chery Tiggo 2.0 liter engine.
cylinder head torque sequence: 7 6 2 4 9 .......................................... 10 3 1 5 8
Is's done in 3 stages 1st stage 45 Nm......
2nd stage 90 degree turn, or a 1/4 turn......
3rd stage 90 degree turn, or a 1/4 turn.......

Camshaft bolts inlet and exhaust share the same torque settings 120 Nm

Cylinder head bolts MUST be replaced.

Main bearing cap Bolts: 1st 45Nm.......
2nd 180 degree turn, or 1/2 turn.......
Connecting Rod Bolts 1st 25Nm......
2nd 90 degree turn or 1/4 turn

Lower cylinder Block bolts 23 Nm........
Camshaft bearing cap bolts: 11Nm

follow this link and click on torque tables and look up your vehicle
http://www.speedwayautoparts.com/index35.htm

Which primera? What year? And what engine?

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?fromSearchPage=true&pageId=0900c152800a9b14&partName=Camshaft+Position+Sensor++CMP&partId=0900c152800a9b14 Here's a guide .just click on link.

Chances are the camshaft is not bad unless it is broke or spun. I would check the cam sensor as well as its connector. If corosion is presant then replace and coat with dyeclectric grease

No it will not run. The timing chain is what turns the Camshft, the Camshaft opens and closes the valves that let fuel into the cylinder and let burnt fuel out.

To Install:

1. Install or connect the following:
   • Timing chain drive sprocket to crankshaft
     1. Rotate the crank so the mark on the sprocket is at the 5 o'clock position
2. Assemble chain to the intake camshaft sprocket alignment copper link to the "INT" diamond timing mark on the camshaft sprocket
   
   NOTE: When lowering the timing chain rotate the assembly 90° to allow the chain to fall between the cylinder block bosses then rotate the assembly back so the camshaft sprocket is facing forward.
   
   
   
3. Lower the assembly through the chain housing opening on top of the cylinder head. Use care to ensure that the chain goes around both sides of the cylinder block bosses NOTE: The crankshaft sprocket timing mark will be at approximately the 5 o'clock position.
   
4. Route chain around crankshaft sprocket and align silver link to the timing mark
   
   NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
   
5. Install or connect the following:
   • Intake camshaft sprocket loosely onto the intake camshaft then install the new camshaft sprocket bolt finger tight NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
     
   • Adjustable timing chain guide through the opening on top of the cylinder head then install the chain guide bolt; torque to 89 lb-in. (10 Nm)
     
     
     
     
   • Exhaust camshaft sprocket loosely onto the exhaust camshaft with the timing mark on the sprocket aligned with the silver link then install a new camshaft sprocket bolt finger tight
   NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
   NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
   
6. Align the camshaft sprocket-to-camshaft then tighten the camshaft bolt using the following procedure:
   
   NOTE: Do not rotate either camshaft more than 1/2 turn in either direction with the crankshaft at Top Dead Center (TDC). To do so may cause valve to piston contact resulting in a damaged valve and/or a damaged piston.
   
   • Ensure that the sprocket timing mark is at the 5 o'clock position
   • Rotate the intake camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
   • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
   • Rotate exhaust camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
   • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
7. Verify that all colored links are aligned with the appropriate marks on the camshaft and crankshaft sprockets NOTE: If they are not repeat steps 1C through 4.
   
8. Install the fixed timing chain guide and bolts; torque to 89 lb-in. (10 Nm)
9. Install the fixed timing chain guide bolt access hole plug; torque to 30 lb-ft. (40 Nm)
10. Install upper timing chain guide and bolts; torque to 89 lb-in. (10 Nm) NOTE: Use a 24mm wrench to support the camshaft while applying torque to the camshaft sprocket bolt. Do not torque the camshaft bolts against the timing chain as it may damage the timing chain.
    
11. Torque the intake and exhaust camshaft sprocket bolts; torque as follows:
    • First Pass: 63 lb-ft. (85 Nm)
    • Second Pass: Turn an additional 30° using a torque angle gauge
12. Install the sealing ring and tensioner assembly; torque to 55 lb-ft. (75 Nm)
13. Install or connect the following:
    • Timing chain oil nozzle and bolt; torque to 89 lb-in. (10 Nm)
    • Camshaft cover assembly
    • Engine front cover
    • Negative battery cable; torque to 13 lb-ft. (17 Nm)

camshaft sprocket bolt torque is 27 ft lbs. the camshaft bearing bolts torque is 9 ft lbs.tighten each bearing cap gradually to prevent binding.your rocker arm bolts torque 6mm bolts to 9 ft lbs and the 8mm bolts to 16 ft lbs.

i have a hyundai getz i require a camshaft sensor can i drive with a faulty one