Where is camshaft position sensor located? - 2002 Cadillac Deville

Google

year make model camshaft position sensor location

We can't GUESS that you have! That Google search query will give you the answer.

The camshaft position sensor on a Peugeot 3008 can be located in different positions depending on the engine model and year of manufacture. Here are the possible locations:

1. On the engine cylinder head: In some Peugeot 3008 models, the camshaft position sensor is mounted on the engine cylinder head, near the camshaft.
2. Near the timing belt cover: In some other models, the camshaft position sensor is located near the timing belt cover. It can be either on the engine block or on the cylinder head.
3. Behind the camshaft pulley: In some Peugeot 3008 models, the camshaft position sensor is located behind the camshaft pulley.

To locate the camshaft position sensor on your specific Peugeot 3008 model, you should consult your owner's manual or a repair manual for your vehicle. Alternatively, you can seek the assistance of a professional mechanic or a Peugeot dealer.

https://www.youtube.com/watch?v=0sUb5CbI6ok

The Camshaft Position (CMP) Sensor is mounted on the cylinder head, front, beneath timing belt cover. The Camshaft Position (CMP) Sensor is located in the right side of the engine compartment at the rear of the valve cover, near the intake manifold. https://www.autozone.com/repairguides/Audi-Cars-1999-05/Component-Locations/Camshaft-Position-CMP-Sensor/_/P-0900c152801c0f2d

(1) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 1
(2) Camshaft Position (CMP) Sensor - Intake Bank 1
(3) Camshaft Position (CMP) Sensor - Intake Bank 2
(4) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 2
(5) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 2
(6) Camshaft Position (CMP) Sensor - Exhaust Bank 2
(7) Generator
(8) A/C Compressor Clutch
(9) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 1
(10) Camshaft Position (CMP) Sensor - Exhaust Bank 1

LOCATION
The camshaft position sensor is located on the rear cylinder bank in front of the exhaust camshaft. The camshaft position sensor extends into the rear cylinder head and is sealed with an O-ring.

see the diagram and videos I found for you. The fir5st one gives a brief overview and removal instructions




2007 Honda Civic Camshaft Crankshaft Position Sensors Location 2010 honda accord camshaft position sensor Google Search Repair Guides Electronic Engine Controls Camshaft Position Sensor AutoZone...

The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor



and next the location of 2003 ford focus camshafts position sensor

2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps

do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal

1. Disconnect battery ground cable. Refer to Section 14-01 .
   

1. Disconnect engine control sensor wiring connector from camshaft position sensor.
   

1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
   

1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
   

1. Remove hold-down clamp (12270) (bolt and washer assembly).
   

1. Remove camshaft position sensor housing from cylinder blocks.
   

Installation

1. CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
   Attach Syncro Positioning Tool T95T-12200-A as follows:
   
   1. Engage camshaft position sensor housing vane into the radial slot of the tool.
   1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.

1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
   

1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
   

1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
   

1. Remove Syncro Positioning Tool T95T-12200-A.
   

1. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
   Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
   

1. Connect engine control sensor wiring connector to camshaft position sensor.
   

1. Connect battery ground cable.