How do you reset maintenance light - 2008 Lexus Rx 350

Reset oil service light Honda Pilot. From years: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.
How do you reset oil service light Honda Pilot. From years: 2003, 2004, 2005.

1. Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
2. Hold the button for at least 10 seconds, until the indicator resets.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

How to reset oil service light Honda Pilot. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.
Resetting the Engine Oil Life Display if maintenance service is done by someone other than your dealer, reset the maintenance minder as
follows:

1. Turn the ignition switch to the ON (II) position.
2. Press the select/reset knob repeatedly until the engine oil life is displayed.
3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
4. Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.

All information is taken from the Honda Pilot owners manual.

There are 2 way to reset the maintenance light on Civic.
1. Manually reset
To reset this maintenance light, you will put the key in the ignition. Next you will press and hold the odometer reset knob, which can be found on the dash where the car's current mileage is located. While you continue holding that know, you will turn the key to the first position but do not start the engine. After about 10 seconds, the maintenance light should disappear. If the light is still on, you can turn off the vehicle and then try the process again. Once the light is off, you are all set until your next schedule maintenance.

2. Hook up a HDS (Honda Diagnostic System) software on a laptop, the light will go off within minutes.

http://www.obd365.com/wholesale/honda-hds-him-diagnostic-tool-with-double-board.html

it tells you maintenance schedule is due and once it is done you have to reset it. resetting instruction can be found in your owners manual, or go online how to reset.

a yellow light indicates maintenance interval has passed whether it b oil change maintenance or egr maintenance,(exhaust gas recirculation valve) can b reset as per ur owners manual.theirs specific instruction in ther on how to reset ur light. maintenance is recommended though,not a good idea to reset an keep driving w/o required maintenance.. hope this helps

Ive never heard of a timing belt light, but there is a maintenance light that can be reset. Here the procedure:

To reset the maintenance reminder light: Turn the ignition switch to the "ON" position. Set the odometer/trip display to the odometer (ODO) mode. Turn the ignition switch off. Depress and hold the trip meter reset button while turning the ignition switch to the on position. The maintenance reminder light will, illuminate for 3 seconds, blink for 2 seconds, illuminate solid for 1 second and then turn off. Release the trip meter reset button. Turn the ignition switch to the off position. Turn the ignition switch to the on position. Confirm that the maintenance light goes out.
Let me know if this helped you out!

You use the button that resets your trip odometer to reset the maintenance light.

with the key in the ignition but not turned on, hold the trip reset button in with one hand. then, while holding the button in, turn the ignition key to the ON position so that the lights on the dash come on.

Continue to hold the reset button in and watch the maintenance light. it will take about 15 seconds for the light to go out

When the light goes out, turn the ignition key OFF and then release the trip reset button.

Your light will be reset and come on in about another 5000 miles to remind you of the next service

Hope that helps

If I remember correctly, on the dash you have a select button. Hold the button down then turn the key on, until the maintenance light blinks and goes out. Turn the key off then back on and your light should be out.

to reset light turn key on hit gas pedal 3 times really fast that will reset it.

a lot of places don't know how to reset the light, all you have to do is step your attentions until you get to maintenance and hold the reset button down it will reset it,