Question about 2001 Nissan Almera Tino

Open Question

How to locate crank sensor

How can i locate a crank sensor on a 2000 nissan tino se2

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
kidspeedy
  • 321 Answers

SOURCE: knock sensor 1996 v6 3.3 nissan pathfinder

The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

Posted on Jun 14, 2009

Ad
c17hydro
  • 2989 Answers

SOURCE: high idle stalls at lights code for crank sensor

Crankshaft and Camshaft Position Sensors Camshaft Position Sensor Engine timing is determined from the relationship between the crankshaft and camshaft. This relationship is maintained by a timing chain or timing belt. The Engine Management System does not control engine timing but it does monitor the relative position and speed of these shafts by monitoring signals generated by sensors. The Engine Management System (EMS) uses signals generated by the camshaft position sensor to synchronize fuel injection to the valve sequence and for the on-board diagnostic procedure for misfire detection. The EMS energizes the injector at or near the time the intake valve opens. For misfire diagnosis, the EMS compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the EMS receives an incorrect number of pulses Diagnostic Trouble Codes (DTC’s) should be stored in the EMS.
If the camshaft position sensor or circuit is faulty most engines will start. Some engine management systems will then default to a pre-programmed injector firing sequence. All injectors may be energized simultaneously or all of the injectors on one bank may be energized at the same time. If the CMP data is required for misfire detection and reliable CMP data is not present misfire detection would probably be suspended.
Related Symptoms The following symptoms can be caused by an intermittent wiring connection or faulty signal to the EMS:

  • Extended crank time with a cold engine
  • Intermittent rough running
  • Unstable idle
  • Bucking
  • Hesitation
  • Stumble
  • Chuggle
  • Poor fuel economy
  • Stalling on acceleration
Crankshaft Position Sensor Engine speed is a very important input to the Engine Management System (EMS). Crankshaft speed and position are the basis for many calculations made by the computer. Crankshaft position values are transmitted to the computer by pickup coils also known as Permanent Magnet (P/M) generators, hall-effect sensors or optical sensors. The Crankshaft Position Sensor (CKP) also known as engine speed sensor is located in close proximity to the crankshaft.
In addition the EMS uses minute variations in the CKP sensor data to determine engine misfire. The EMS uses this information in conjunction with the camshaft position sensor to perform misfire diagnostics.
Related Symptoms: No Start/Intermittent Start Condition – Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit

Posted on Jun 23, 2009

HyeProfile
  • 35 Answers

SOURCE: sensor locations

Here's the diagnostic procedure for DTC code 0340, directly from the service manual:

8f57ac3.jpg
a08cb42.jpg
ce6092c.jpg
b3a9ad5.jpg
e76f3a6.jpg
5a415d6.jpg
f69cd27.jpg

Posted on Aug 05, 2009

  • 1 Answer

SOURCE: Speed sensor location on a Nissan Maxima 2000 GXE...

There are two speed sensors one is called a revolution sensor that is located on the case of the transmission. You can take the driver side wheel off and see the sensor on the top of the case of the transmission. A 10mm bolt is holding it in. Easy fix

Posted on Jun 17, 2010

  • 1114 Answers

SOURCE: knock sensor 2000 nissan xterra V6, location of

Hello the sensor is located under your intake manifold you will need to remove the intake manifold to gain access to it here is photos of what and where your looking for thisregeetone_0.pngregeetone_21.jpg

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan almera tino Crankshaft sensor location, please help as I need to change mine, already got part


U sure its the sensor..dont guess. Cud b an egr valve or vacuum leak. Car wudnt run at all w a bad cranksensor. Git car scand to target area

Jan 12, 2016 | Nissan Cars & Trucks

1 Answer

Location of nissan almera tino crankshaft sensor


if you are under the car it should be on the firewall side. It is black piece or a light grey color.

Jan 08, 2016 | Nissan Cars & Trucks

1 Answer

I have a nissan almera tino 2011 se2 petrol the immobilisor has been activated and i cant get my car to start i only have one key help!!!


if you havent got the key to reset it then you done for im afrai you eather need to get a new key that will do it or send it to a garage

Sep 19, 2013 | Cars & Trucks

1 Answer

2000. Nissan frontier. V6. P335 trouble code won't go away crank position sensor


If you have replaced the crank sensor and the code comes back, it may be a problem with the wiring harness or connector, or the plate the sensor reads.

Sep 26, 2012 | 2000 Nissan Frontier

1 Answer

Where is crank sensor located on nissan maxima 3.0


crank sensor is at the bottom of the crank pulley. right under neith the pulley is a 2 wire sensor bolted to the engine with 2 bolts.

Sep 18, 2012 | 2000 Nissan Maxima

1 Answer

Where is the crank position sensor located on a 2000 Altima 2.4


I changed one on a 03 sentra and it was under the car by the exhaust entering the crank case. You can not miss it because it is the only object with a wire that is mounted to your engine block. Crank sensors will be close to the crank and cam sensors are close to the cam. I hope that this info helps.

Aug 04, 2012 | 2000 Nissan Altima

1 Answer

Failed emissions test nissan tino


Mine just failed emissions test garage said its burning oil what is the soulution

Apr 19, 2012 | 2004 Nissan Nissan almera tino

1 Answer

Nissan Almera Tino Diesel 2.1 - Temperature control not working


Hi there, very common on these vehicles, you need to remove the heater cotrols and check that the cable hasn't come out, usually the clips that hold the cables in place break causing the heaters to not work properly, Nissan do modified clips now to stop it from happening, it may need a cable too if its too far bent, hope this helps.

Jun 03, 2009 | 2000 Nissan Maxima

Not finding what you are looking for?
2001 Nissan Almera Tino Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...