it will say in your owners manual but i believe you turn your ignition key to the run position not the start. and pump the gas pedal 3 times with in 5 seconds

Anonymous

1959 Answers
Posted on Jul 15, 2009

SOURCE: how to reset the change oil light on a 2003 chevy

Information courtesy of synthetic-direct.ca
Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
Best of luck.
Greg

Anonymous

174 Answers
Posted on Nov 09, 2009

SOURCE: how do you reset the computer on a 2007 chevy

You can reset most computers by unhooking the battery for a few minutes. I usually leave them for an hour over lunch break.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

2helpful

2answers

2007 Chevy Silverado Classic. Location of oil sending unit please?

Question edited for clarity.
Question moved to model category.

If you have a 4.3 or 5.7 Litre engine (Silverado Classic Body Style), it is mounted on the back of the intake manifold in a brass fitting just under where the fuel lines come up from the transmission bell housing.
Jun 4, 2013

I have a 2007 chevy silverado and need to replace the oil ...

Read full answer

Aug 16, 2023 • 2007 Chevrolet Chevrolet Silverado 1500...

0helpful

1answer

Recently changed the oil for my 04 silverado, but the change engine oil warning will not go off, how do i correct this

After changing the oil and filter, reset the monitor by proceeding as follows:

Turn ignition On, but do not start engine.

Fully depress and release accelerator pedal three times within five seconds.

If CHANGE ENGINE OIL lamp flashes for five seconds, this indicates system has reset.

Start engine. OIL LIFE should change to 100%.

If CHANGE OIL SOON lamp lights again, repeat reset procedure.

2001-08 Silverado, w/Driver Information Center

Turn ignition On, but do not start engine.

Press MODE button until DIC (Driver Information Center) reads OIL LIFE LEFT/HOLD SET TO RESET.

Press and hold SET button until 100 percent is displayed. You will hear 3 chimes and CHANGE ENGINE OIL SOON message will go off.

Turn ignition Of

how to reset oil life on 2004 chevy silverado

Read full answer

Nov 10, 2016 • Cars & Trucks

1helpful

1answer

Smog Filed due to error P0121 Throttle/Pedal Position Sensor/Switch A Circuit range/performance.

Replacing TPS will reset the light but will stay in memory until the computer is reset. For help to change throttle body sensor check out you tube :How To Install Replace Throttle Position Sensor Chevy Silverado GMC Sierra.

Read full answer

Mar 23, 2015 • 2007 Chevrolet Silverado 1500 2WD

0helpful

1answer

Chevy duramax check engine 2500hd check engine light came on after i took it to a chevy dealer to have the oil changed took it to auto zone to code it and no code came up could this be a fuse or did c

take it back to the dealer and have them reset the oil change data on the computer.. thats the issue with this jeep we have here .. they did not reset the oil change interval in the computer..simple fix.. sorry they overlooked it or the tech got lazy..

Read full answer

Dec 08, 2013 • 2006 Chevrolet Silverado 3500

0helpful

1answer

2007 Chevy Silverado oil pressure gauge fluxuating, setting off computer on dash reading "engine oil low" also warning bell sounds. Thanks!

If you are lucky , replacing the oil pressure sender unit will solve the problem. Your truck might have perfectly good oil pressure , but a bad sensor. OR you might actually have low oil pressure , which is not good , and will be expensive to fix. Good luck.

Read full answer

Dec 15, 2010 • 2007 Chevrolet Silverado 1500 2WD

0helpful

1answer

How do i clear the change engine oil soon message. It's a 2007 silverado.

The "Change Oil" message displayed on your Chevrolet Silverado's gauge cluster is part of the Oil Life Monitoring System, standard on many GM (General Motors) vehicles. The message appears when it's time for an oil-change; the interval is based on your driving habits (for example, it may appear more frequently if you engage in a lot of stop-and-go traffic). Once you change your Chevy's oil, the message will not disappear; the system must be reset. The process is a bit different between Chevy Silverado models.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); }); Difficulty: Moderately Easy Instructions

Step 1 Insert your key and turn the ignition to position "C" (Run/On) without starting the engine.
Step 2 Press the second button from the top on your information center (next to the steering column, car symbol) until "Oil Life" displays on your odometer cluster.
Step 3 Press and hold the "Reset" button on your information center (check mark symbol) until the "Oil Life" display changes to 100 percent.
Step 4 Turn your ignition to position "A" (Lock/Off).
Step 1 Insert your key into the ignition, and turn it to position "A" (Run/On) without cranking the engine.
Step 2 Depress the gas pedal three times within five seconds. The "Change Oil" message will begin to flash.
Step 3 Turn the ignition to position "A" (Lock/Off) once the light stops flashing (about 10 seconds).