SOURCE: Changing the wiper motor on a 1997 Audi A3
Here you will find the replacement of the wiper motor for Audi A4. Maybe similar for Audi A3! First you must diagnose your problem. In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works. Heed of the windscreen !!! Refit all in reverse order. Success!
SOURCE: how to adust audi a3 door, it has dropped about
if hinges are in good order, then ,with the door ajar "adjust" by grabbing hold of the bottom of the door edge and lifting upwards a little at a time to get correct fit,a common problem with heavy doors nowadays....
SOURCE: how to check transmission fluid on a audi a3 1997
IF TRANSMISSION DONT HAVE FILLER TUBE AND DIP STICK.YOUR VECHICLE HAS LEVEL CHECK PLUG ON TRANSMISSION OIL PAN TOWARD EXHAUST END.YOUR VECHICLE HAS TO BE LIFTED UP LEVEL ON JACK STANDS.ENGINE HAS TO BE RUNNING.AND TRANSMISSION FLUID TEMPERATURE HAS TO BE 95 TO 113 DEGREES. SHIFT TRANSMISSION THROUGH ALL GEARS TWICE THEN BACK TO PARK.MAKE SURE ALL DRIVE WHEELS OFF THE GROUND AND VECHICLE IS FIRM AND SECURE ON JACKSTANDS.WHILE ENGINE RUNNING REMOVE LEVEL CHECK PLUG.REAR OF TRANSMISSION PAN. IF TRANSMISSION FLUID DRIPS YOUR FLUID LEVEL OKAY.IF TRANSMISSION FLUID POUR OUT CHECK PLUG HOLE YOU HAVE TOO MUCH FLUID IN TRANSMISSION.IF NO FLUID COME OUT ADD TRANSMISSION FLUID RIGHT SIDE OF THE TRANSAXLE IN FRONT OF THE DRIVE SHAFT.WARNING THIS VECHICLE TRANSMISSION FLUID SUPPOSE TO BE CHECKED AT A GARAGE ON LIFT. YOU CAN CHECK FLUID AT HOME IT IS DANGEROUS THE ONLY THING YOU NEED TO MAKE SURE VECHICLE ON SOLID LEVEL GROUND AND JACKSTAND SECURE SOLID NO MOVEMENT WHAT SO EVER.
SOURCE: what are the torque settings
The torque settings for a 1997 Audi A3 1.6 cylinder head:
1. Tightening sequence
2. Cylinder head instructions:
2.1. Renew bolts: Yes.
3. Tightening torques:
3.1. Stage 1 - Tighten: 40 Nm.
3.2. Stage 2 - Tighten: 90 degrees.
3.3. Stage 3 - Tighten: 90 degrees.
Please do rate my response. Thanks!
Fig. The 1.8L cylinder location as viewed from the front of the vehicle. The firing order is 1-3-4-2
The above is for an Audi A4 from 1997. I didn't find an A3, unfortunately, in the U.S. market, on the Autozone.com website.
45 views
Usually answered in minutes!
×