Question about 2001 Subaru Outback
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Very simple. Only one of a few things. First off. Push the up and down switch, listen, if there is a humming sound, your actuator may be fine. You window may be off track. If it is not off track, and there is a humming sound, then it may be the master switch. They are not that expensive. If it is not the master switch, the only other two things it could be is the up/down button or the connectors under the button. I hope that helped you out. Good luck and let me know. Have a great day.~MWD
Posted on Mar 26, 2009
Posted on Aug 09, 2009
This is not your average timing belt replacement due to being a double overhead cam that is also an interferance fit.First remove cooling fans.2-Loosen drive belts and remove.3-Remove crank pully.4-Remove timing covers.You will see 4 cam sprockets.Theses sprockets contain single and double referance marks.You will be using the double referance marks.Rotate engine until the double referance marks are facing each other.This is to be done the same way that the American autos timing Chain systems are done but you will have 2 small double lines to line up not dots.The next step is the most important step and is of utmost imortance.THE CAMSHAFT HAVE TO BE LOCKED IN PLACE--FAILURE TO DO SO CAN RESULT IN BENT VALVES.The cam sprocket holders can be bought or rented.You can make your own as well by making 2 wedges with bolt through the middle.Slip in between sprockets and tighten enough to hold sprockets.Do not use excessive torque while tightening wedges sprockets are not made of steel but rather a composite material.Next you will have to remove the tenioner.The tensioner has to be retracted and pin istalled to hold in retracted position.The tension device has to be retracted with care or will be damaged.You can not exceed 50 pounds pressure on the plunger.The simplest method is to reract while still in vehicle, it takes 15 minutes to properly retract the plunger.By pulling up on the tensioner by hand with about 18 pounds of force --50 will be exerted at the plunger.When fully retracted insert pin to hold in reracted position.Next check to make sure that cam wedges are holding and no sprocket are trying to move,when satisfied remove one of the rollers at the bottom on the side where you left hand would be standing in front.Pull off belt.Replacement belt will have referance marksone line will go to crank sprocket face up others will line up with other sprocket marks.Reinstall roller followed by tensioner then pull pin you have holding tenioner retracted.Remove wedges.Reinstall covers fans belts.Do not be intimitaded by this replacement.Everything is very easy to get to.Be sure cams are locked and that damage is not done to tensioner and it is straight forward.
Posted on Nov 06, 2009
Tips for a great answer:
Aug 01, 2016 | 2005 Subaru Legacy Outback
May 14, 2015 | 2003 Subaru Outback
Jan 29, 2014 | 2002 Subaru Outback
Nov 26, 2012 | 2001 Subaru Legacy Outback
2006 Subaru Liberty 3.0 Blitzen, 52,000kms. It's unbelievable, both my low beams went out at once and when I checked it was both the globes had gone at once. Never has this happened on any other vehicle before, I've ordered a HID conversion kit over the net, hope that works well.
Oct 03, 2012 | 2006 Subaru Outback
May 17, 2010 | 1997 Subaru Outback
Feb 09, 2010 | 2001 Subaru Outback
Jun 09, 2009 | 2001 Subaru Outback
Jul 06, 2014 | 2001 Subaru Outback
35 people viewed this question
Usually answered in minutes!