Question about 1991 Jeep Wrangler

1 Answer

How to install a serpentine belt on a 1991 jeep wrangler with a 2.5 engine without power steering

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Jeep Expert
  • 496 Answers

There should be a sticker in the engine compartment that shows the routing and you should be able to hold the tensioner back with a 3/8's ratchet with a long handle.

Posted on Jan 26, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Mike258
  • 1498 Answers

SOURCE: 1993 jeep wrangler 4cyl -serpentine belt digram

f45e20e.jpg

Hope this helps,

Mike

Posted on Jul 14, 2008

  • 508 Answers

SOURCE: what do you loosen to remove serpentine belt from

There is an idler pulley close to the power steering. Loosen the bolt that goes through the front of the idler pulley first. Then you will see the head of a bolt looking up at you. Turn the bolt clockwise to tighten and counterclockwise to loosen. The pulley is attached to the threaded bolt and it moves the pulley up or down as needed to adjust the belt tension. When the belt is replaced turn the bolt until the belt is tight. Remember to check the belt again after a few hundred miles. A new belt will stretch and loosen.

Posted on Dec 08, 2009

ZJLimited
  • 17970 Answers

SOURCE: i need diagram for serpentine belt installation on 1999 jeep .

Check HERE for few engine sizes:
- 1999 JEEP WRANGLER - L4 2.5L 150ci GAS FI N P
- 1999 JEEP WRANGLER - L6 4.0L 242ci GAS FI N S

Hope this help (remember comment and rated this post).

Posted on Apr 09, 2010

  • 6982 Answers

SOURCE: how do i replace serpentine belt on 1997 jeep wrangler

Adjustment is made by loosening the power steering pump. There is a transverse long bolt (jack bolt) right under the pump that is used for adjustment.

Posted on Aug 02, 2010

Mike258
  • 1498 Answers

SOURCE: How do you remove the

Hi Alex,

They are a pain the first time. There is a deceptively easy trick to it. I wrote out the step by step for taking it off / putting it on.

Click here for the trick

Hope you find it helpful

Mike

Posted on Dec 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free belt diagrams


http://serpentinebelthq.com/1991-jeep-wrangler-yj-4-0l-serpentine-belt-diagram/ her is a link for you to a diagram. I hope this helps

Jul 08, 2014 | 1991 Jeep Wrangler

1 Answer

2002 Jeep Wrangler Screeching Sound On Startup until Engine is warm.


NEVER NEVER USE BELT DRESSING. It's sticky and attracts grit that destroys your pulleys. Screeching is almost always caused by a worn belt tensioner. Read these posts

http://ricksfreeautorepairadvice.com/diagnose-a-belt-tensioner/
http://ricksfreeautorepairadvice.com/diagnose-belt-noise/

Aug 16, 2017 | 2002 Jeep Wrangler

2 Answers

I may have installed the serpentine belt incorrectly on my 1998 Jeep Wrangler with the 4.0 eng and AC. I am having problems with the engine overheating. Can you send me a diagram of the correct way to...


this is for a system with a/c. If you don't have a/c let me know and I will get you the correct one but i'm sure that you have a/c and power steering.


360dreamworx_55.gif

Aug 26, 2011 | 1998 Jeep Wrangler

1 Answer

How do i replace serpentine belt on 1997 jeep wrangler


Adjustment is made by loosening the power steering pump. There is a transverse long bolt (jack bolt) right under the pump that is used for adjustment.

Aug 02, 2010 | 1999 Jeep Wrangler

1 Answer

Looking for serpentine belt diagram for a 1998 jeep wrangler 2.5 liter engine


hi i have a picture i can email it to you, my email is
steve_e_morris@hotmail.com
and i will send attachment of picture, it has 3 types, one with no power steering, one with power steering, and one with power steering and a/c hope this will help

Aug 01, 2010 | 1998 Jeep Wrangler

1 Answer

Need routing diagram for serpentine belt - '98 Jeep Wrangler, straight six with and without A/C


Click of the following direct, Free Link. It has several Serpentine Diagrams, including the one for your 1998 Jeep Wrangler 4.0L In-Line 6-Cylinders based upon your Engine Options (AC/No AC, Power Steering/No Power Steering, etc.).
The Link Page ALSO has the 2.5L In-Line 4-Cylinder Serpentine Belt Diagrams with their various engine options.
Included are the with AC / without AC Routing.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/1998/make/jeep/model/wrangler/1998_jeep_wrangler_drive_belt_routing_diagram.htm

Apr 13, 2010 | 1998 Jeep Wrangler

1 Answer

I need diagram for serpentine belt installation on 1999 jeep wrangler.


Check HERE for few engine sizes:
- 1999 JEEP WRANGLER - L4 2.5L 150ci GAS FI N P
- 1999 JEEP WRANGLER - L6 4.0L 242ci GAS FI N S

Hope this help (remember comment and rated this post).

Apr 09, 2010 | 1999 Jeep Wrangler

1 Answer

What do you loosen to remove serpentine belt from 1991 jeep wrangler with ac and power steering. thanks 4 cyl. 2.5


There is an idler pulley close to the power steering. Loosen the bolt that goes through the front of the idler pulley first. Then you will see the head of a bolt looking up at you. Turn the bolt clockwise to tighten and counterclockwise to loosen. The pulley is attached to the threaded bolt and it moves the pulley up or down as needed to adjust the belt tension. When the belt is replaced turn the bolt until the belt is tight. Remember to check the belt again after a few hundred miles. A new belt will stretch and loosen.

Dec 08, 2009 | 1991 Jeep Wrangler

1 Answer

Belt replacements


Hi Saul,

I've got an '86 Cherokee Laredo 2.6L and a '91 Wrangler too. It's got a 4.0L inline six cylinder. But it has a serpentine belt.

Comment me back and tell me which components will be attached to the belt in question. That way I can tell you which of them gets used to install the belt.

You will need a socket set and a pry bar for the procedure.
Let me know
Mike

Jun 13, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...