Blower motor slk200 05

Ford Escort Heater AC Blower Motor Removal - YouTube

? 4:49
https://www.youtube.com/watch?v=oAWn-ybZJUs
Aug 28, 2013 - Uploaded by richpin06a
Ford Escort Heater AC Blower Motor Removal. ... How To Fix Install AC Heater Fan Blower Motor 1991-03 ...

Remove the passenger side, lower dash cover under the glove compartment that conceals the blower motor. A 1/4-inch socket will be needed to remove the screws holding the cover. Locate the blower motor. The motor can be seen hanging down close to the passenger kick panel, disconnect the electric to the blower motor and then remove the screws that secure it to the ducting, drop blower down and out from under the dash. I would test the blower first with a 12 volt jumper cord from the battery made out of house lamp cord, it is not usually the problem but the blower speed control module that is next to it.

Hello! it's my job to make things as easy for the customer as possible...Therefore I must ask why you want to replace the heater switch? Is it because you have lost one or two of the switch speeds? Your vehicle is noted for loss of the Blower Motor Resistor...
Changing the Heater switch means removal of the Climate Control Assembly which is not the easiest of jobs...I've included the process...But are you sure the blower resistor is OK? If you have lost 1,2, or all blower motor speeds it's more than likely the Resistor pack. And a lot easier to change...
Guru...saailer


Remove climate control:

1. Remove the instrument cluster finish panel...
   

1. Remove the 3 climate control assembly screws...

1. Disconnect the climate control assembly vacuum connector...

1. Disconnect the 5 climate control assembly electrical connectors...

1. Remove the climate control assembly..

Removal of blower motor Switch:

1. Remove the climate control assembly.
   

1. Remove the blower motor switch knob.

1. Remove the blower motor switch.
   1. Remove the screw.
   1. Remove the blower motor switch.

Removal of blower motor Resistor:



Blower Resistor is under the battery tray...

MOTORCRAFT Part # YH1698 ...cost $25



Guru...saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Removal & Installation

The front blower motor is located in the front passenger's right side foot well area.

1. If additional access is needed, remove the front passenger's right side lower kick panel.
   
2. Detach the electrical connectors from the blower motor.
   
3. Remove the fasteners on the blower motor mounting flange.
   
4. Remove the blower motor downward from the blower unit.
   
5. Installation is the reverse of the removal procedure.
   

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 25; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

Blower Motor Removal & Installation To Remove:

1. Remove the coolant recovery and windshield washer fluid reservoir assembly.
2. Disconnect the blower motor electrical connector.
3. Remove the 2 screws that retain the acoustic cover in the blower motor area.
4. Cut the acoustic cover between the 5 clip lands.
5. Retain the piece of the acoustic cover for reassembly.
6. Remove the cooling tube from the motor.
7. Remove the screws that retain the blower motor to the case.
8. Remove the blower motor from the case.
9. Inspect the flange of the blower motor for damage or distortion. Damage or distortion will cause an air leak.
10. Repair the flange as necessary.
11. Inspect the blower fan for damage and distortion.
12. Repair or replace the blower fan as necessary.

To Install:

1. Installation is the reverse of removal.

Section 12-02A: Heating and Defrosting, Ranger, Explorer 1995 Aerostar/Ranger/Explorer Workshop Manual REMOVAL AND INSTALLATION Blower Motor and Blower Motor Wheel Assembly Removal and Installation

1. Remove the windshield washer bottle.

1. Position the speed control servo out of the way (if so equipped), refer to Section 10-03A.

1. Disconnect the wire harness connector from blower motor by pushing down on the connector tabs and pulling the connector off the blower motor .
   
   
   
   
   Item Part Number Description 1 18527 Blower Motor 2 19A786 Blower Motor Housing Tube 3 - Heater Case Insulator
   (Part of 19850) 4 19930 Blower Housing 5 - Electrical Connector
   (Part of 19805)

1. Disconnect the blower motor housing tube (19A786) at the blower motor .

1. Remove three screws attaching the blower motor to the A/C blower housing (19930) .

1. Holding blower motor housing tube aside, pull the blower motor from the heater plenum chamber case (18A484) and remove it from the vehicle.

1. Remove the blower wheel hub pushnut and, if applicable, the clamp from the shaft. Then, pull the blower motor wheel (18504) from the shaft. For installation, follow removal steps in reverse order. Check system for proper operation. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.
   

SECTION 412-02: Heating and Ventilation 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001 Blower Motor Removal

1. Remove the footwell upper trim panel (passenger side).
   • Remove the pushpins.

1. Remove the blower motor.
   1. Disconnect the electrical connector.
   1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.

Installation

1. NOTE: Engage the securing tab for the blower motor.
   

Follow your vehicle's service manual procedures for blower motor removal. The following are general removal procedures:

• Disconnect the negative battery cable.
• Disconnect the blower motor lead connector from the wiring harness connector.
• Remove the blower motor cooling tube from the blower motor.
• Remove the four retaining screws.
• Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
• Lift up on the blower and remove it from the blower housing.
• Installation the new blower motor by reversing the removal steps.
• Connect the negative battery cable.

REMOVAL

1. REMOVE GLOVE COMPARTMENT DOOR
1. REMOVE BLOWER MOTOR
1. Disconnect the connector from the blower motor.
2. Remove the 3 screws and the blower motor.

INSTALLATION
Installation is in the reverse order of removal.

SECTION 412-04: Control Components 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Blower Motor Resistor Removal

1. Remove the upper footwell trim panel (passenger side).
   • Remove the pushpins.

1. Disconnect the blower motor resistor electrical connector.

1. Remove the blower motor resistor.

-------------------------------------------------------------------------