Key stuck in ignition lincoln zephyr

If a problem occurs with the SecuriLock system, the indicator will flash
rapidly or glow steadily when the ignition is in the 3 (RUN) position.
just look at the lamp carefully.

all you need to do is see this, error and you know why IMMO cuts spark and engine will not start, BY DESIGN
check all fuses
scan the PCM see why IMMO fails
you said
chip key replacement<<< what does that mean, a lock smith or online hacker made, or what.? hacks do not work.
or mobile lock smith did this?
does engine crank or not. if yes and IMMO blinks wrong ,IMMO is not happy.
with key on LOCK pos. this lamps blinks to warn thieves, PROTECTED so find car with keys left in the car, not yours.

Key Stuck in Ford Fusion (2006 model) - YouTube

? 1:21
https://www.youtube.com/watch?v=3LVQttFOzGA
Jun 18, 2014 - Uploaded by Jessica East
#Ford #Fusion #Key #ignition #Stuck #FordFusion2006. ... i have a 2006 mercury milan and my key got stuck in there last night,... it to park with a little bit of force. will see what happens next time. good video, nice to know.

Key Stuck in Ignition While in Park

www.2carpros.com/.../2007-ford-fusion-key-stuck-ignition-while-park
Dec 16, 2012 - KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION FORD:2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan

If it is an automatic. make sure it is in park. There is a cable that allows the key to be removed only when in park

Might have a low battery mate... I suggest if you have a friend that will let you use their battery just to see if it will start... Then if it dose go and buy a new one.. remember all batteries are different. Check with the sales rep to see whats best for your car

It is located on cylynder # 5

There's a TSB published by ford for this condition. It's caused by a binding shifter button.


Printable View (73 KB) TSB
07-14-7

• KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION

Publication Date: July 6, 2007
FORD: 2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan
This article supersedes TSB 07-2-1 to update the Part List. ISSUE: Some 2006-2007 Fusion, Milan and 2006 Zephyr vehicles built before 9/4/2006 may exhibit a customer concern of the ignition key getting trapped or a shifter slider binding condition. Most of the key trapped conditions are caused due to a binding shifter button which does not allow the pawl to contact the park detect switch.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE If the key will not release from the ignition cylinder lock follow the Key Trapped procedure. On vehicles with a hard-to-shift shift lever into park or slider bunching/binding then follow the Shifter Slider Binding procedure. Key Trapped:

1. Actuate knob button 5-10 times, observe for binding or sticky condition.
2. Replace knob assembly if the knob sticks following Workshop Manual (WSM), Section 307-05. NOTE: WHEN REPLACING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR.
   

Shifter Slider Binding:

1. If shifter slider is bunched up or binding, replace bezel assembly following WSM, Section 307-05. NOTE: WHEN REPLACING THE BEZEL, CARE NEEDS TO BE TAKEN TO ENSURE THAT THE BRAKE SHIFT INTERLOCK OVERRIDE TAB IS PROPERLY ALIGNED INTO ITS GUIDE. REFER TO FIGURE 1.
   
   
   Figure 1 - Article 07-14-7
   
   NOTE: WHEN REINSTALLING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR. NOTE: IF OVERRIDE CAP IS DAMAGED DURING REPAIR, IT IS AVAILABLE SEPARATELY.
   

PART NUMBER PART NAME 6E5Z-7D443-B Bezel Asy-Black w/FNR5 Trans (Fusion-Milan) 6E5Z-7D443-C Bezel Asy-Black w/Aisin F21 Trans (Fusion-Milan) 6H6Z-7D443-A Bezel Asy-Satin Nickel (Zephyr) 6E5Z-7213-C Knob Asy-Black (Fusion-Milan) 6H6Z-7213-A Knob Asy-Charcoal (Zephyr) 6H6Z-7213-B Knob Asy-Charcoal-OD (Zephyr) 6E5Z-7A214-B Override Cap-Black (Fusion-Milan) 6H6Z-7A214-A Override Cap-Satin Nickel (Zephyr) W790088-S901 Screw (2 Req)
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME 071407A 2006-2007 Fusion, Milan And 2006 Zephyr: Replace Knob Assembly, Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.3 Hr. 071407B 2006-2007 Fusion, Milan and 2006 Zephyr: Replace Bezel Assembly Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.4 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 7213 69

NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.

Copyright © 2007 Ford Motor Company

try pulling the door handle a time or two, perhaps the latching mechanism is stuck in the latched position. sometimes pulling the handle and moving the latch with a screwdriver is needed. if this doesn't work then try lifting up on the door while shutting it, if this works then you need new door hinge bushings or new door hinges

check the inside fusebox, at location f20, this is the fuse # location F 20, this fuse operates the dsp module which is the digital signal processing. check that fuse.also check F4. now look under the hood and check these two fuses in that box, fuse 23 (F23) and fuse 19 (F19). hope this helps.

turn ignition key on. now jiggle key gently while simultaneously gently rocking steering wheel. hopefully you will feel a release.