Cruise control doesnt disengage when brake applie

Do you know how it works ? What controls it ?

Did you hook up a scan tool an check for DTC'S - diagnostic trouble codes ?

Cruise Control Description and Operation
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions. However, steep grades may cause variations in the selected speeds. The electronic cruise control system has the capability to CRUISE, COAST, RESUME SPEED, ACCELERATE, TAP-UP or TAP-DOWN.
The main parts of the cruise control system are:
• The powertrain control module (PCM)
• The function control switches
• The stop lamp switch assembly
The cruise control system uses the powertrain control module (PCM) to maintain the desired vehicle cruise speed . The PCM assembly contains a low speed limit which will prevent system engagement below a minimum speed of 40 km/h (25 mph). The PCM assembly is not serviceable.
Cruise control operation is controlled through the function control switches located on the multifunction turn signal lever. The cruise control function control switches includes the ON/OFF, SET/COAST, R/A (resume/accelerate). The switch assembly provides driver control of the cruise control system.
The stop lamp switch is used to disengage the cruise control. A cruise control release switch circuit and a stop lamp switch circuit are used. The stop lamp switch is mounted to the brake pedal bracket . To disengage the system the driver presses the brake pedal. The speed of the vehicle at brake actuation will be stored in the memory of the PCM.
With cruise control, the vehicle can maintain a speed of about 40 km/h (25 mph) or more without keeping your foot on the accelerator. When the driver turns off the cruise control ON/OFF switch or ignition switch, the cruise control turns off. The vehicle speed stored in the memory of the PCM will be lost.
Ignition positive voltage is supplied from the HVAC fuse, to the cruise control switch. When the cruise control ON/OFF switch is on, ignition positive voltage is applied to the cruise on switch signal circuit terminal of the PCM. If the driver has not pressed the brake pedal, ignition positive voltage is supplied through the stop lamp switch, TCC/Brake signal contacts to the cruise control brake pedal switch signal circuit terminals of the PCM. Cruise control is canceled when the driver presses the brake pedal. The stop lamp switch contacts close, applying battery positive voltage to the stop lamp signal circuit of the PCM. At the same time, the TCC/Brake contacts of the stop lamp switch open and voltage is removed from the brake pedal signal circuit at the PCM. When pressing the SET/COAST button on the multifunction turn signal lever, ignition positive voltage is applied to the set/coast switch signal terminal of the PCM. When pressing the R/A (resume/accelerate) on the control switch, ignition positive voltage is applied to the resume/accelerate switch signal terminal of the PCM.
When the cruise switch is in the ON position, and the driver presses the SET/COAST button, the PCM then checks to see that the cruise control enable criteria is met. If the cruise control criteria has been met the PCM sends a class 2 message to the instrument panel cluster (IPC) to illuminate the cruise light.
The PCM will inhibit cruise control:
• When the PCM detects that the center high mounted stop lamp (CHMSL) in not operating properly.
• When vehicle speed is less than 40 km/h (25 mph).
• When in PARK, REVERSE, NEUTRAL, or 1st gear.
• With low engine RPM
• With high engine RPM (fuel cut-off)
• When vehicle speed is to high
• When an over or under charged battery voltage condition exists
• Antilock brake system/traction control system is active for more than 2 seconds
If the PCM determines that any of the cruise control inhibit conditions are present, the PCM will disengage the cruise control. If the PCM disables the cruise control for an inhibiting event it will record the reason for disengagement in the Disengage Definition data file.

Do you know how to test electrical circuits with a DVOM - digital volt ohmmeter, looking at a wiring diagram for the CC so you know what wires to test , if not your best bet might be to take it to a qualified repair shop .

Cruise control only maintains speed by utilizing the accelerator. To speed up it increases it and during slowing is removes it. The cruise control will not apply brakes in the event of a steep downhill run. In this case the vehicle will start to accelerate in the same manner as if the cruise control was not engaged. But in theses cases, most cruise controls, once the speed exceeds a certain amount above the set speed, will auto-disengage as a safety feature.

ADJUST YOUR BRAKE LIGHT SWITCH IT IS TOO SENSITIVE SAME AS DISENGAGING WHEN BRAKE IS APPLIED.

The cruise control is normal disengaged by applying a little pressure to either the clutch or brake pedal. There are switches/sensors on the top of these pedals near the return springs. The retuns springs become weaker with time/use, so it is possible that they are not fully returning to allow disengage to reset so that it can be used again.
That is the cheapest fix and should be the first check.
The next is to cange the stalk as the switch at the end may be broken. Costwise it is relatively inexpensive for a replacement and to instal yourself. Make sure you've done the first part, or else you'll waste money and time.
Good luck.

If you brake lights stay on and the cruise control doesn't work then I would be looking at the brake light switch at the top of the brake pedal as if there is power passing through it then it cuts out the cruise control. The same as if you put your foot on the brake cuts out the cruise control. The hatch button will be another problem like a fuse or broken cable or failed latch solenoid. As to the rear middle brake light try checking the bulb first.

The brake light switch, located on the brake padal assembly, is and input to the cruise control module. When the switch fails keeping the lights on is makes the cruise control module think you are applying the brakes when infact you are not. Chek the switch wiring for damage and if ok replace the switch making sure you adjust it properly.

Check that the cruise control module fuses are not blown in the fuse panel. Also make sure your stop lights are working; cruise controls are designed to disengage when the brakes are applied, and one method of sensing that is to monitor brake light current.


then reset your four wheel drive again

Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .
Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

the brake light switch is part of your cruise control circuit. check the adjustment. it should be threaded so that you can change the depth on it. probably not your switch at all.

bad ground on right side