Question about 2004 Chrysler Pacifica
Tie rod is broken off of right and left front tire
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
To make it easier, when you stop at autoparts store, ask for a "crowsfoot wrench'" to fit the new inner tie rod. Should be able to get it in 3/8' or 1/2 " drive to fit ratchet. It's basically the end of an open end wrench, with square drive for ratchet to fit into.
Posted on Apr 23, 2009
I use to work at a chrysler dealership and worked on these cars all the time, it was an ongoing problem because the tie rods were designed like **** (unservicable) they are not hard to change though. you can do it yourself you just need to count or mark the threads when you remove it so that your alignment (steeering adjustment) does not change. Or find a local guy, you might find someone on craigslist, people are hungry for work and will work for their money. also if you get the part aftermarket rather than the from the dealer the part is cheaper. dealers jack up the part price 20% - 60%. try partstrain.com or similar sites.. also search coupon codes on the net when your ready to order, often sides like this offer 10 buck or a percentage off.. itll be worth the time. good luck.
Posted on May 02, 2009
if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.
Posted on May 18, 2009
yes. If the rack is not held ,when you try to turn the rod you could bend the rack.With the pin out it doesn't take much to hold the rack,loosen the end with the rack "turned " so the rack is retracted into the housing,not sticking way out .
Posted on Aug 21, 2009
Testimonial: "Thanks a bunch"
You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned
Posted on May 06, 2010
Testimonial: "Thanks for the advice - will work on it this weekend. Quick and timely response."
Tips for a great answer:
Oct 02, 2017 | Chrysler Cars & Trucks
Oct 04, 2016 | 2005 Chrysler Pacifica Touring
Jul 05, 2015 | 2005 Chrysler Pacifica Touring
May 04, 2015 | 2005 Chrysler Pacifica
Jul 14, 2012 | 2006 Chrysler Pacifica Touring
Jun 25, 2010 | 2005 Chrysler 300
Jan 07, 2010 | 2005 Chrysler Pacifica
Dec 14, 2009 | 2004 Chrysler Pacifica
Sep 18, 2009 | 2004 Chrysler Pacifica
Mar 11, 2009 | 2005 Chrysler Pacifica
May 16, 2019 | 2004 Chrysler Pacifica
83 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: