Sales Weekly Specials New Vehicles New Vehicle Specials Pre-Owned Vehicles Pre-Owned Specials Apply For Credit Latest Newspaper Ads Internet/Fleet Quick Quote Specials Test Drive Car Finder Finance Apply For Credit Specials Service Specials Service Appointment Parts Specials Parts Request About Us 2011 Mopar Car Show News/Events Departments Employment Directions Contact Us
SOURCE: 1994 cutlass supreme--security light on--car won't start
take to dealer and have them reprogram the computer
SOURCE: Security light flashing and car won't start now
does it start at all, or does it run for about 1 second and shut off? if the latter, then it's the passlock system, and he could have a defective key or security module. the keys have a predetermined resistance value which activates the passlock system to prevent hotwiring. If it is the passlock system, then sometimes you have to wait 15-20 mins for it to reset before starting the engine.
SOURCE: 1994 oldsmobile 88 won't start
if key has a chip in it the lock cylinder is bad it has wires that sense that chip i've got a new one pluged it in at base of steering column with new key in it and used old key as normal
SOURCE: Service AWd light is on on my 98 olds bravada
i got a 98 bravada and my AWD light was on, what i did to fix it was replace the transfer case motor and thats all, i did a bunch of research and found out that the transfer case motor is the main conponent with of your AWD it tells the transfer case when to give the front wheels power. try replacing that
SOURCE: When I start my 2001 alero the anti-lock, traction
the anti-lock and traction lights will come on together if there is a common problem with the two, since they are closely related. may be a wheel speed sensor or something similar. the service engine soon light indicates a problem with the engine computer, can be anything from an emission system problem or an engine performance problem. all of these lights can come on with no apparent running problems on the car. the service vehicle soon light is basically a maintenance reminder, an oil change light. take the car into a shop and have the codes read for these lights.
1. Insert new key into ignition cylinder and turn it to the ON (RUN) position. The security light on the dash will flash for fifteen minutes.
2. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder OFF and then back to the ON (RUN) position. The security light on the dash will flash for fifteen more minutes.
3. When the security light stops flashing, you have FIVE minutes to start the next step. Turn the ignition cylinder to OFF and then back ON (RUN) position. The dash will flash for fifteen more minutes.
4. After the security light stops flashing the third time, the new key has been programmed into the vehicles computer and will operate the car. It has replaced ALL the previous electronic key codes and is the ONLY key programmed into the vehicles computer.
If you want to add a key....
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within 15 seconds, insert the new key and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming the key into the vehicle.
5. Don't attempt to start the vehicle with any key for at least 1 minute.
<HR>On-Board Programming Method "C"
for Ford keys (Later 1998-newer Ford, Lincoln, Mercury)
If you want to initiate a new master key....
1. This requires that the vehicle be connected to special dealer equipment. There are two ten minute delays involved while this device erases all existing key programming and sets up the vehicle computer to accept new key codes. Two new keys should be ready because the system requires a minimum of two keys in the program. After the first two keys are programmed, additional keys can be entered individually by following the instructions for adding duplicate keys (below).
If you want to add a key....
**You must have two original keys to perform this procedure. If you only have one key, you WILL have to take it to the dealer to get it programmed**
1. Insert and existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (RUN) and back to OFF. Ignition should stay on for at least ONE SECOND.
3. Remove the existing key and, within TEN seconds, insert a second working key and turn it to ON (RUN) and the back OFF. Ignition must be in ON for at least ONE second, but no more than TEN seconds. Remove the key.
4. Insert the new key before TWENTY seconds have elapsed and turn it to ON (RUN). Leave it the ON position for at least ONE secondand turn back to OFF.
5. The security light will light up for THREE seconds to indicate that the new key has been successfully programmed.
6. To program additional keys, repeat steps 1 through 5
As a precautionary measure for all of the above procedures, you should wait at least one minute after you have performed this until you start your vehicle.
62 views
Usually answered in minutes!
×