How to change oil pan - 2005 GMC Sierra 1500 Hybrid

1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket

Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

need motor 4cy or 6cy

There is a sensor in the oil pan. It measures the amount of oil in there. It may have gone bad, That or you may have a piece of trash ( something blocking the sensor), just enough to not get a proper reading. Just before your next oil change, you and add some Marvels Mystery, or oil type flush fluid, to the oil to help clean the engine and oil pan. If that doesn't work, time to change a sensor. Dealer item (sorry, it costs). Then drop the pan, change the gasket, clean the pan and lowers(bottom of the engine, where pan is), change sensor, and gasket, remount pan, fill with oil and thats it

Do you need to replace the oil pan it self or just the oil pan seal? This can been a DYI job, depending on your experience working with cars. You will need a your basic tools. (Jack Stands, Jack, Oil Container, wrenches and sockets, new oil and filter.) The first thing you will need to do is drain the oil. This is a good time to change your oil since you will be taking the oil pan completely off.
Steps to removing oil pan
1) Set car on jack stands or ramps in order to work under the car. (Be Safe, Be Smart!)
2) You will need a wrench or socket to remove oil drain plug and drain the oil out of the car
-This is a good time to change your oil, so replace oil filter as well.
3) Once the oil is drained you can take of the oil pan off. Most oil pans are just bolted. Not to hard to take of.
4) Once off this is a good time to clean the oil pan if your just replacing the gasket. Do not use lubricant cleaners like wd-40. Brake cleaner has worked for me, you can also ask your local auto shop or autozone for a good cleaner.
5)Replace the oil pan with new gasket making sure there are no tears in gasket and it sits well between the oil pan and engine block. (Make sure there is nothing in the oil pan as well that could cause harm)
6) once you replaced the oil pan its just as simple as putting oil back into your car like you are changing your oil.

If you do not know where the oil pan Is I would really consider getting help with your first oil change. The pan is on the bottom of the motor and has a plug on the bottom of it which is used to drain. The key is not to over tighten/strip the plug when putting back on. Make sure the oil filter is changed and tightened properly. It is def not a bad idea to have a 2nd person so assist for your first oil change!!

YOUR OIL PAN GASKET IS ATTACH TO TOP OF OIL PAN.WHICH SEAL TO ENGINE BLOCK.YOU NEED A HAYNES REPAIR BECAUSE YOU HAVE TO REMOVE RIGHT MANY THINGS TO GET OIL PAN OFF TO GET TO GASKET.

have car jacked up and blocked for safety,drain oil from engine and remove the oil pan bolts,remove pan.

if the owner is the one going to change the oil pan , then the owner should locate the oil pan .Prepare the the equipment going to be used in changing the oil pan. First drain the oil or the engine oil that is in the oil pan. In draining, the owner of the car should twist the drain plug until it loose that the oil will spill on a can or to where the owner will place the engine oil.The oil pan is connected to the engine with the bolts . The owner have to twist the bolts until the oil pan is being place out of the engine . then replace the oil pan .Then the owner have to place back the bolt using the bolts to connect the oil pan to the engine twist the bolts again until the new oil pan is connected to the engine.Close or twist the drain plug until engine oil will not spill , Then refill or place engine oil to the engine. If the owner cannot do it then the owner have to go to a car mechanic to do the task or the job.

Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Remove protective bottom plastic cover under engine to gain acces to oil pan plug at the back of oil pan. Remove oil pan plug, drain old oil; replace oil filter. Replace plug and fill with oil. Replace plastice guard ubder engine.