How do Iremove front seat? - 2002 Subaru Forester

Check if the rear lights are faulty, if ok remove computer fuse to cancel code.

what year, why make it so hard to get help from the blind.?

OIL PAN
Removal & Installation
1. Disconnect negative battery cable. Remove engine torque strut. Raise and support vehicle. Drain
crankcase. Disconnect oil level sensor electrical connector. Remove oil level sensor and oil filter.
Disconnect front exhaust pipe from manifold. Remove right front wheel and splash shield.
2. Disconnect oil cooler pipes. Disconnect A/C compressor electrical connector. Remove A/C compressor,
and position aside. Disconnect engine mounts from frame.
3. Remove flexplate access cover. Use transmission jack at transaxle to raise engine. Remove oil pan bolts
and oil pan. To install, reverse removal procedure. Install oil level sensor after oil pan is installed. Tighten
retaining bolts to specification. See TORQUE SPECIFICATIONS.

Removal instructions can be found here CLICK HERE

1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

their is a bolt fixing on the inside of the chassis just under the drive shaft ,two straps hold this tank up and they clip in on the outside and a 13mm headed bolt on the innermost side

Head Restraints Removal

1. Unscrew front seat head rest guide rod retainers (610A18) .
   

1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
   

1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
   

Installation

1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
   

1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
   

1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
   

1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .
   
   Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
   

1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .
   

How To Install Replace Front Control Arm Pontiac Sunfire Chevy Cavalier...

Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:

• It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
• The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).

• The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
• Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.

----------------------------------------------------------------------------------------------

Removal

1. Unscrew front seat head rest guide rod retainers (610A18).
   

1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
   

1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
   

Installation

1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
   

1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
   

1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
   

1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
   

1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.
   
   Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.