Cat pallet jack 2wp4500 won't lift - Cars & Trucks

See these 2 links:

https://www.forkliftaction.com/forum/thread.aspx?trid=15046

https://www.forkliftaction.com/forum/thread.aspx?trid=12064

Probably have to take it apart as something got jammed in there or the spindle/bearings broke. Contact the manufacturer for parts and a diagram.

There is a wide range of wood species available that is best suited for different purposes. Hardwoods were mainly used in ancient time for building pieces of furniture. Whereas softwoods are used for many other purposes. Pine is considered to be the best wood for designing pallets. You can check Palletower to get some more idea about the different types of wood.

Is it a manual pallet jack? At the base of the arm you will see a lever that the handle controls (usually it is at the end of the chain). Assist the lever by pushing it in further than the handle can able. That should allow the lift to lower. Sometimes the pallet needs to be level to lower. If it is a powered lift, check the limit switches. Good luck!

If it's blowing a fuse then that usually means somewhere there's too much electricity.

I dropped the tank on a 34' Fleetwood with the same situation. The jacks were welded on so there was no removal option. What I did was (1) Cut eight 4x4 s into 12" sections. I bolted 4 sections together to make a "pad". One 8" 4X4 makes two pads. (2) Then I pumped the fuel into drums. Free drums are easy to find. A cheap 12V fuel pump and tubing is available from any auto supply. (3) I raised the camper on all 4 jacks. Than I retracted one jack, set a pad in place under it and extended the jack fully. Clockwise I put pads under all the jacks one at a time to make a layer. Then I put in another layer of jacks, round and around, and continued until the camper was up 4 layers. (4) The camper could "roll" forward off the jacks at this point because the wheels were off the ground. I attached a chain to the camper frame and took tension backwards using a come-along chained to a tree. (5) Then I got some pallets from the grocery store trash and put those under the tank. (6) I loosened the hangers for the tank and let it down on the pallets slowly. The hoses have to be removed before the tank drops very far. I worked the pallets out one layer at a time to lower the tank to the ground. (7) I could reach the pump mounting plate so I just removed the screws and lifted out the pump and gasket. (8) installation was the reversal.

If I had to do it again, I would take it to Camping World or a truck garage. They have lifts to raise the camper and jacks to raise and lower the tank.

The Door has 2 lifting "shocks" on either side - these provide a reduction in door weight, to make it easier to lift the door ( it's heavy!) These lifts have a compression socket that fits onto a ball on the vehicle. Popping the strut end off of the ball with a flat bladed screwdriver will allow you to open further - BUT it will also disable and lifting assistance, and the door will not stay open on its own. If you decide to pop off one end of the strut for loading purposes, you'll need to cut a piece of wood to keep the door open for loading.
As I do NOT recommend this ( it could cause grave personal injury if the wood falls out or is bumped, and it could destroy that door if it falls ) It would be better to use a trailer for transporting whatever you're getting on pallets!!
Hope this helps and thanks for using Fixya!

This is a lift truck (pallet lift). First put the switch to the on position, then on the keypad press the number one button, then the green button.

toyato pallet jack electric , DISCUSSION FORUM - Forkliftaction.com

www.forkliftaction.com/forum/thread.asp?trid=15922

Dec 24, 2014 - 4 posts - ‎2 authors
California, United States, I have 7hbw23 toyota pallet jack with error codes c14 and e115 e112 trying to find code list or repair manual any ... toyota pallet jack . Discussion about troubleshooting ...
7 posts
Dec 30, 2014
Error Messages for Walkie 102XM. Discussion about ...
9 posts
May 6, 2009
More results from www.forkliftaction.com

Forum discussions - FORKLIFTACTION, Search this ...

www.forkliftaction.com/search/search_results.aspx?searchall=y...3

RESULTS 1 - 20 - 7HBW23 pallet jack no power, no fault codes. Lifting machines ...Toyota Electric pallet jack. Lifting machines ... error code C-28. Mechanical ...

toyota forklift manual 7hbw23 code c14 pdf - P(1) - srdt.sotite ...

srdt.sotite.com/pdf/1/toyota-forklift-manual-7hbw23-code-c14.html

Toyota electric pallet jack 7hbw23manual.pdf - WordPress.com ... I have 7hbw23toyota pallet jack with error codes c14 and e115 e112 trying to find code list or.

Code c-14 for toyota electric pallet jack - Fixya

www.fixya.com/cars/t12123378-code_c_14_toyota_electric_pallet_jack

Mar 22, 2012 - I have code c-14,try to fix it ... Hi Danny: One of the things that I do is to try to help resolve the problem, and that does not always mean answering ...

I would use floor jacks and jack it up from the back as high as it will go and then set jack stands under it. Its front will drive so you dont have to worry about it rolling just make sure its in park and if its standard make sure its in gear. Be good to block the front wheels also.