2006 DODGE 3500 HUB BOLT TORQUE - 2006 Hyundai Accent

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

I need more info. Is this a 1500--2500--3500, 4wd or 2wd?

The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

The torque for the hub bolts is 120 ft. lbs
The torque for the axle nut is 185 ft. lbs.

Hello acadiamaine,

If the shock absorber bolt to the axle is a 14mmX1.5 it should be torqued to 110 Nm if it is a 12mmX1.5 bolt torque it to 70 Nm.

The bolt to the frame side should be torqued to 140 Nm if the axle bolt is 14mmX1.5 and 80 Nm if the axle bolt is 12mmX1.5.

I hope this helps.

Regards,

Jerry

front hub nut ( axle shaft ) 185 ft lbs.

there are three mounting bolts behind the wheel studs
remove the bolts
remove abs sensor
slide the hub out of steering knuckle

Tight tight rtight tight and so on alternating criscross pattern

theres an access cover under the turbo on the front of the bellhousing (2 10mm bolts) that you have to remove to access the bolts that hold the flywheel to the flexplate. kinda like removing the bolts to a torque converter. flywheel is real hevy though, watch your fingers

You have to remove the axle shafts first as it has a full-floating axle, then pull rotor and hub off the axle housing. Unbolt rotors from hub. Check bearings and seals in hubs and the axle snouts where the bearings run before installing. Put new flange gaskets on axle and torque flange bolts to 95 ft-lbs.