SOURCE: 2000 elantra po455 code evap emission control
Large leak?... Fuel Cap not tight or the wrong one is installed. Also, the charcoal canister close valve may be stuck 'open' AND/OR the purge control solenoid valve may be stuck 'closed.'
SOURCE: trouble code shows po452 which is the evap
P0452 Evap.Emission System-Pressure Sensor Low Input
The evaporative emission control system prevents hydrocarbon vapors from escaping from the fuel tank into the atmosphere where they could form photochemical smog. Gasoline vapors are collected in the charcoal canister. The Fuel Tank Pressure Sensor (FTPS) is an integral part of the evaporative monitoring system. The PCM monitors the FTPS signal to detect vacuum decay and excess vacuum. The FTPS measures the difference between the air pressure inside the fuel tank and outside air pressure to check the purge control solenoid valve operation and for leak detection in the evaporative emission control system by monitoring pressure and vacuum levels in the fuel tank during the purge control solenoid valve operating cycles.
P0440 Evaporative emission (EVAP) system - malfunction
Possible causes: Hose connection(s), intake leak, EVAP canister purge valve
P0441 Evaporative emission (EVAP) system - incorrect flow detected
Possible causes: Hose connection(s), intake leak, EVAP canister purge valve
P0442 Evaporative emission (EVAP) system - small leak detected
Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve
P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction
Possible causes: Wiring, EVAP canister purge valve, ECM
P0444 Evaporative emission (EVAP) canister purge valve -open circuit
Possible causes: Wiring open circuit, EVAP canister purge valve, ECM
P0445 Evaporative emission (EVAP) canister purge valve -short circuit
Possible causes: Wiring short circuit, EVAP canister purge valve, ECM
P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction
Possible causes: Wiring, EVAP pressure sensor, ECM
P0455 Evaporative emission (EVAP) system - large leak detected
Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve
P0456 Evaporative emission system - very small leak detected
Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor
P0457 Evaporative emission system - leak detected (fuel cap loose/off)
Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor
P0458 Evaporative emission system, purge control valve -circuit low
Possible causes: Wiring short to earth, EVAP valve
P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve
Evaporative Emission Purge Solenoid
Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.
53 views
Usually answered in minutes!
×