Question about 2001 Lincoln Town Car

1 Answer

Can the exciter ring on rear axle be replaced 200 lincoln town car

I installed a new axle but be for installing axle had to drive wheel studs in ,in doing so hit the exciter ring at the top edge,straightened it out finished installing.now the abs light comes on speed o does no0t always work right and brake s are weird.Exciter ring be replaced or do i need another new axle??

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 85,206 Answers

The ring is part of the wheel hub assembly

Posted on Dec 28, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 651 Answers

SOURCE: 1995 lincoln town car Rear air suspension problem

probably a leak in the system. check the switch in the trunk, make sure it is on.

Posted on Jan 10, 2009

  • 1 Answer

SOURCE: how do I fix the turn signal on my 93 town car

The flasher is located in the fuse box under the dash on the left side of steering wheel and the flasher is in there. If that is what is wrong with them.

Posted on Jul 01, 2009

  • 103 Answers

SOURCE: "Chk Trac light" on 2000 Lincoln Town Car

MAKE SURE TIRES ARE ALL THE SAME SIZE FIRST OF ALL,NEXT MAY HAVE A SPEED SENSOR NOT OPERATING PROPERLY OR BENT OR MISSING EXCITER RING ON FRONT HUB OR REAR AXLE. EITHER WAY THERE IS AN ABS FAULT OR A DIFFERENCE IN WHEELSPEED ON ONE OF THE FOUR WHEELS CAUSING TRAC LIGHT TO ILLUM. VEHICLE THINKS YOU ARE LOSING TRACTION AND APPLYING ABS AND MISFIRING VEHICLE TO SLOW DOWN UNTIL TRACTION IS RECOVERED

Posted on Jul 19, 2009

Tnsiouxfalls
  • 617 Answers

SOURCE: just had car dealership repair 1997 lincoln town air ride

Those Lincolns are notorious for that,I'd just get a set of coil springs out of a Crown Victoria cop car(junk yard)and swap them out.Done it many times,you can do it in about an hour,and they'll never leak down again.By the way,there's some O-rings in that system.Make some soapy water and spray every connection,just maybe you'll get lucky.

Posted on Nov 10, 2009

agent91
  • 2100 Answers

SOURCE: rear air shocks 1998 lincoln continental deflate when parked

My Grandma marquis did the same thing, I thought that was normal, it slowly goes down when you shut it off and slowly goes up when you start it, It didn't hit the ground or anything, but then it finally did die altogether, years later, and then it hit the ground, so I got regular shocks back there and it rode fine, stayed level, it is now resting in the junkyard in a shallow unmarked grave. It was a nice car.

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear axle


lincoln town car has rear axle continental is front wheel drive

Nov 12, 2012 | 1997 Lincoln Continental

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

1 Answer

Need to remove rear axle to replace tire studs


You don't need to remove the axle. Remove the rotor or drum. pound out the broken studs with a hammer. Install the new stud into the hole. Use a wheel nut and some washers to pull the new stud into place. They also make a stud installer tool which makes it a little easier.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Dec 02, 2010 | Ford Expedition Cars & Trucks

1 Answer

We have a 2005 chevy uplander (AWD) with a broken lug nut stud on a rear tire. Looks like we have to get into the reare axle hub. How difficult is this? thanks


I have never done one on this vehicle but have replaced many on all other cars over the years, this is what i experienced, the stud will pound out with a good 2-3 lb. hammer, and the new stud and nut will get pulled back through the empty hole by use of a strong impact wrench...start the stud by hand try to pull it as much as you can through the splined hole in the axle flange, install the new nut backwards on the stud screw it down as far as you can then with the 1/2' drive impact wrench on full throttle tighten the lug nut...by doing this you are pulling the stud through the void hole.
Please remeber to use a small amount of axle grease on the new stud and hole prior to installing the replacement stud and nut.
You prbably have to remove the disc brake caliper and brake pads along with the rear disc brake rotor to gain access to the stud, there should be an access hole also allowing you to get behind the axle flange for removal and installation.
Hope this works.
Happy Motoring!!

Jul 11, 2010 | 2005 Chevrolet Uplander

1 Answer

My left back tire of a 1991 Lincoln towncar fell off & i was trying to replace rear lugnuts studs


remove all brake components off of that side, pound out studs towards center of the car with a hammer. place the new studs through the back of the axle and then use washers that just fit over the studs for spacers, and put the lugnut on the stud and tighten until the new stud is seated on the back flange of the axle. remove the lugnut and repeat for the rest of the studs.

Mar 20, 2010 | 1991 Lincoln Town Car

1 Answer

"Chk Trac light" on 2000 Lincoln Town Car


MAKE SURE TIRES ARE ALL THE SAME SIZE FIRST OF ALL,NEXT MAY HAVE A SPEED SENSOR NOT OPERATING PROPERLY OR BENT OR MISSING EXCITER RING ON FRONT HUB OR REAR AXLE. EITHER WAY THERE IS AN ABS FAULT OR A DIFFERENCE IN WHEELSPEED ON ONE OF THE FOUR WHEELS CAUSING TRAC LIGHT TO ILLUM. VEHICLE THINKS YOU ARE LOSING TRACTION AND APPLYING ABS AND MISFIRING VEHICLE TO SLOW DOWN UNTIL TRACTION IS RECOVERED

Jul 19, 2009 | 2000 Lincoln Town Car

1 Answer

How to replace lug studs on 2002 chrysler town


I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Jul 08, 2009 | 2009 Chrysler Town and Country

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

2 Answers

Rear wheel bearing


SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Apr 10, 2009 | 2004 Ford GT

Not finding what you are looking for?
2001 Lincoln Town Car Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

gerry bissi

Level 3 Expert

4388 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...